DG213DQ-E3
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Weight | 172.98879mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2009 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 110Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 500mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG213 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Power Supplies | 512/+-15V |
| Number of Channels | 1 |
| Max Supply Voltage | 40V |
| Min Supply Voltage | 3V |
| Operating Supply Current | 1μA |
| Power Dissipation | 500mW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 130 ns |
| Number of Inputs | 4 |
| Voltage - Supply, Single/Dual (±) | 3V~40V ±3V~22V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 100 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 60Ohm |
| Min Dual Supply Voltage | 3V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 90 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| On-state Resistance Match-Nom | 1Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 130ns, 100ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 1 Ω |
| Crosstalk | -95dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Height | 920μm |
| Length | 5.08mm |
| Width | 4.4mm |
| RoHS Status | ROHS3 Compliant |
DG213DQ-E3 Overview
Presented in 16-TSSOP (0.173, 4.40mm Width), this electrical component is convenient for overseas shipping. High reliability is provided by advanced packaging method Tube. It is mounted in the position Surface Mount. Multiplexers and demultiplexers have a ratio of 1:1. Around -40°C~85°C TA is the extended operating temperature. In total, 16 terminations have occurred. A electrical component with 1 channels is capable of high-quality output. When a voltage supply of 15V is used, the electronic component should be turned on and run. A total of 16 pins are injected into the body of the electronic part. The analog switch ics are built using SPST - NO/NC switching circuits. Try searching for DG213 variants of the analog switch ic. In this multiplexer, the internal resistance is 110Ohm. For functions related to 16 pins, please refer to the datasheets. In this analog multiplexer, the value is Multiplexer or Switches. In normalcircumstances, users should not exceed 40V volts for the multiplexer. Digital switch that provides Dual, Single power at a cost-effective price. It is recommended to use 3V as the lowest voltage for the electrical part. 1μA current would be enough for this multiplexer to operate. When the digital multiplexer is charged above 1μA, damage can occur. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 22V. The voltage should be at least 3V if you are using dual power supplies. A total of SEPARATE OUTPUT outputs are available on this analog switch ic. Operating the 4 inputs requires 4 inputs.
DG213DQ-E3 Features
1 Channels
Switch Circuit: SPST - NO/NC
1μA Supply Current
DG213DQ-E3 Applications
There are a lot of Vishay Siliconix DG213DQ-E3 Analog Switches & Multiplexers ICs applications.
- Cell phones
- Sample hold systems
- Communications systems
- 65 V DACs
- ATM
- RGB switches
- Digital access cross connects
- Cross Connects
- Communication systems
- Channelized and Unchannelized DS3 applications
