Parameters |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-SOIC (0.154, 3.90mm Width) |
Number of Pins |
16 |
Weight |
547.485991mg |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
Published |
2009 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
Resistance |
110Ohm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
640mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
15V |
Terminal Pitch |
1.27mm |
Time@Peak Reflow Temperature-Max (s) |
40 |
Base Part Number |
DG213 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Power Supplies |
512/+-15V |
Number of Channels |
1 |
Max Supply Voltage |
40V |
Min Supply Voltage |
3V |
Operating Supply Current |
1μA |
Nominal Supply Current |
5μA |
Power Dissipation |
640mW |
Max Supply Current |
1μA |
Throw Configuration |
SPST |
Turn On Delay Time |
130 ns |
Number of Inputs |
4 |
Voltage - Supply, Single/Dual (±) |
3V~40V ±3V~22V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
100 ns |
Max Dual Supply Voltage |
22V |
On-State Resistance (Max) |
60Ohm |
Min Dual Supply Voltage |
3V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
90 dB |
Current - Leakage (IS(off)) (Max) |
500pA |
Channel Capacitance (CS(off), CD(off)) |
5pF 5pF |
On-state Resistance Match-Nom |
1Ohm |
Switch Circuit |
SPST - NO/NC |
Switch Time (Ton, Toff) (Max) |
130ns, 100ns |
Charge Injection |
1pC |
Channel-to-Channel Matching (ΔRon) |
1 Ω |
Crosstalk |
-95dB @ 100kHz |
Switching |
BREAK-BEFORE-MAKE |
Height |
1.55mm |
Length |
10mm |
Width |
4mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
DG213DY-E3 Overview
Due to its 16-SOIC (0.154, 3.90mm Width) packaging, the electronic part is convenient for international shipping. This high-reliability packaging method uses advanced packaging methods Tube. Multiplexers like this are mounted in the Surface Mount position. Multiplexer and demultiplexer circuits have a number 1:1. Extended operating temperature around -40°C~85°C TA. Totally, there are 16 terminations. High-quality output is provided by the electronic component's 1 channels. If the voltage supply is 15V volts, the electrical component should be turned on and run. It is injected into the electrical part body with 16 pins. A SPST - NO/NC switching circuit is used for these analog switches. If you are looking for variants of the digital switch, trying search with DG213. As far as internal resistance is concerned, it has 110Ohm. Datasheets for functions of 16 pins are available. This switch device is a typical Multiplexer or Switches. In normalcircumstances, users should not exceed 40V volts for the multiplexer. The digital multiplexer has a low cost Dual, Single supply. In order for the electronic part to function properly, the lowest voltage should be 3V. For this multiplexer to operate, 1μA current would be sufficient. The switch multiplexer may be damaged if it is exposed to voltage greater than 1μA. For this multiplexer, dual supply voltage is feasible, but it should not exceed 22V. In the case of dual power supplies, you should connect at least 3V. SEPARATE OUTPUT outputs are utilized by this digital multiplexer. The 4 inputs need to be operated in order to work.
DG213DY-E3 Features
1 Channels
Switch Circuit: SPST - NO/NC
1μA Supply Current
DG213DY-E3 Applications
There are a lot of Vishay Siliconix DG213DY-E3 Analog Switches & Multiplexers ICs applications.
- Battery Powered Instruments
- Signal routing between systems
- Imaging
- Fiber to the Home
- E1 Network Equipment
- Mechanical reed relay replacement
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Fiber In The Loop (FITL)
- ATM
- Transmit