DG213DY-T1
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Weight | 547.485991mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 60Ohm |
| Terminal Finish | TIN LEAD |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 640mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Power Supplies | 512/+-15V |
| Number of Channels | 1 |
| Max Supply Voltage | 40V |
| Min Supply Voltage | 3V |
| Power Dissipation | 640mW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 130 ns |
| Number of Inputs | 4 |
| Voltage - Supply, Single/Dual (±) | 3V~40V ±3V~22V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 100 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 60Ohm |
| Min Dual Supply Voltage | 3V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 90 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| On-state Resistance Match-Nom | 1Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 130ns, 100ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 1 Ω |
| Crosstalk | -95dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Height | 1.55mm |
| Length | 10mm |
| Width | 4mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
DG213DY-T1 Overview
Packed in 16-SOIC (0.154, 3.90mm Width), the electronic component is convenient for shipping overseas. In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. It is mounted in the position Surface Mount. There is 1:1 ratio between the number of multiplexers and demultiplexers. An extended operating temperature of -40°C~85°C TA degrees Celsius. Totally, there are 16 terminations. The electronic part provides high-quality output because it has 1 channels. A 15V voltage supply should turn on and run the electronic component. It is part of the design of the 16 series that this electronic component is included. A SPST - NO/NC switching circuit is used to build these analog multiplexers. Internally, this switch multiplexer has a resistance of 60Ohm. To find out what the functions of 16 pins are, please refer to their datasheets. In this analog multiplexer, the value is Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 40V to the switch device in normal circumstances. Analog switch ics with Dual, Single supply type are cost-effective. There should be 3V voltage fed to the electrical part below 3V. Putting voltage greater than 1μA on the multiplexer may cause damage. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 22V. You should attach at least 3V voltage if you are using dual power supply. The digital multiplexer has SEPARATE OUTPUT outputs that can be used. Operating 4 inputs is required.
DG213DY-T1 Features
1 Channels
Switch Circuit: SPST - NO/NC
DG213DY-T1 Applications
There are a lot of Vishay Siliconix DG213DY-T1 Analog Switches & Multiplexers ICs applications.
- 65 V DACs
- Optical Applications
- Medical Instrumentation
- RGB switches
- Digital Cross-Connects
- Automatic test equipment
- PBX interfaces
- Sample-and-hold systems
- Microprocessor controlled systems
- Existing multiplexer applications (both fault-protected and nonfault-protected)
