DG213DY-T1-E3

130ns, 100ns SPST - NO/NC 60Ohm Analog Switches BREAK-BEFORE-MAKE DG213 16 Pins 500pA 15V 16-SOIC (0.154, 3.90mm Width)

Manufacturer: Vishay Siliconix
Nocochips NO: 880-DG213DY-T1-E3
Package: 16-SOIC (0.154, 3.90mm Width)
Datasheet: PDF
Stock: 623
Description: 130ns, 100ns SPST - NO/NC 60Ohm Analog Switches BREAK-BEFORE-MAKE DG213 16 Pins 500pA 15V 16-SOIC (0.154, 3.90mm Width)(Kg)

Details

Tags

Parameters
Factory Lead Time	1 Week
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	16-SOIC (0.154, 3.90mm Width)
Number of Pins	16
Operating Temperature	-40°C~85°C TA
Packaging	Tape & Reel (TR)
Published	2009
JESD-609 Code	e3
Pbfree Code	yes
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	16
Resistance	110Ohm
Terminal Finish	Matte Tin (Sn)
Subcategory	Multiplexer or Switches
Max Power Dissipation	640mW
Technology	CMOS
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	4
Supply Voltage	15V
Terminal Pitch	1.27mm
Time@Peak Reflow Temperature-Max (s)	40
Base Part Number	DG213
Output	SEPARATE OUTPUT
Pin Count	16
Power Supplies	512/+-15V
Number of Channels	1
Max Supply Voltage	40V
Min Supply Voltage	3V
Operating Supply Current	1μA
Nominal Supply Current	5μA
Power Dissipation	640mW
Max Supply Current	5μA
Throw Configuration	SPST
Turn On Delay Time	130 ns
Number of Inputs	4
Voltage - Supply, Single/Dual (±)	3V~40V ±3V~22V
Supply Type	Dual, Single
Neg Supply Voltage-Nom (Vsup)	-15V
Turn-Off Delay Time	100 ns
Max Dual Supply Voltage	22V
On-State Resistance (Max)	60Ohm
Min Dual Supply Voltage	3V
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	90 dB
Current - Leakage (IS(off)) (Max)	500pA
Channel Capacitance (CS(off), CD(off))	5pF 5pF
On-state Resistance Match-Nom	1Ohm
Switch Circuit	SPST - NO/NC
Switch Time (Ton, Toff) (Max)	130ns, 100ns
Charge Injection	1pC
Channel-to-Channel Matching (ΔRon)	1 Ω
Crosstalk	-95dB @ 100kHz
Switching	BREAK-BEFORE-MAKE
Drain to Source Resistance	60Ohm
Height Seated (Max)	1.75mm
Length	9.9mm
Width	3.9mm
Radiation Hardening	No
RoHS Status	ROHS3 Compliant
Lead Free	Lead Free

DG213DY-T1-E3 Overview

Packed in 16-SOIC (0.154, 3.90mm Width), the electronic component is convenient for shipping overseas. High reliability is provided by advanced packaging method Tape & Reel (TR). The multiplexer is located in Surface Mount. 1:1 is the ratio between multiplexers and demultiplexers. Increasing operating temperature to around -40°C~85°C TA. The total number of terminations is 16. High-quality output is provided by the electronic component's 1 channels. Powered by a 15V voltage supply, the electrical part should be switched on and run. A total of 16 pins are injected into the electrical part body. Based on SPST - NO/NC switching circuits, these analog multiplexers work. Try searching with DG213 to find analog multiplexer variants. This digital multiplexer has 110Ohm internal resistance. The functions of 16 pins can be found in the datasheets. In this analog multiplexer, the value is Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 40V. Analogue multiplexers of the Dual, Single supply type that are cost-effective. 3V is the lowest voltage the electrical component should receive. The analogue multiplexer could operate on 1μA current. It may damage the digital multiplexer if the voltage is higher than 5μA. For this switch, a dual supply voltage is feasible, but it must not exceed 22VIf you are using a dual power supply, you should attach at least 3V. There are SEPARATE OUTPUT outputs on this analog switch ic. Operating the 4 inputs requires 4 inputs. Drain to Source resistance is 60Ohm.