DG221BDJ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Weight | 1.627801g |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2007 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 90Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 470mW |
| Technology | CMOS |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Reach Compliance Code | unknown |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 15V |
| Max Supply Voltage | 18V |
| Min Supply Voltage | 13V |
| Power Dissipation | 470mW |
| Max Supply Current | 1.5mA |
| Turn On Delay Time | 550 ns |
| Number of Inputs | 4 |
| Supply Type | Dual |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 340 ns |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 90Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 5nA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 9pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 550ns, 340ns |
| Charge Injection | 20pC |
| Crosstalk | -90dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Drain to Source Resistance | 90Ohm |
| Normal Position | NC |
| Voltage - Supply, Dual (V±) | ±15V |
| Height | 3.81mm |
| Length | 21.33mm |
| Width | 7.11mm |
| RoHS Status | Non-RoHS Compliant |
DG221BDJ Overview
Due to its 16-DIP (0.300, 7.62mm) packaging, the electronic part is convenient for international shipping. A high level of reliability can be achieved through the use of an advanced packaging method Tube. This analog switch is mounted in Through Hole. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Around -40°C~85°C TA is the extended operating temperature. In total, 16 terminations have occurred. A 15V voltage supply should turn on and run the electronic component. It is injected into the electrical part body with 16 pins. A SPST - NC switching circuit is used to build these analog multiplexers. A 90Ohm internal resistance characterizes this multiplexer. For functions related to 16 pins, please refer to the datasheets. This switch device is a typical Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 18V to the switch device in normal circumstances. A analog switch ic that has a cost-effective Dual supply type. There should be 13V voltage fed to the electrical part below 13V. Put voltage above 1.5mA on the multiplexer to cause damage. For this multiplexer, dual supply voltage is feasible, but it should not exceed 18V. For dual power supplies, a voltage of at least 7V should be attached. This analog switch ic utilizes SEPARATE OUTPUT output. Operating voltages of 15V are compatible with the electrical part. A 4 input needs to be operated. There is 90Ohm resistance between Drain and Source for this electronic part.
DG221BDJ Features
Switch Circuit: SPST - NC
Drain-to-Source resistance: 90Ohm
DG221BDJ Applications
There are a lot of Vishay Siliconix DG221BDJ Analog Switches & Multiplexers ICs applications.
- Remote Powered Equipment
- Audio signal routing
- PBX interfaces
- Communication systems
- Medical
- Isolation
- Video switching
- Power routing
- Microprocessor Controlled Analog Systems
- FTTH
