DG221BDJ-E3
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Weight | 1.627801g |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2009 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 90Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 470mW |
| Technology | CMOS |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Base Part Number | DG221 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Operating Supply Voltage | 15V |
| Number of Channels | 1 |
| Max Supply Voltage | 18V |
| Min Supply Voltage | 13V |
| Operating Supply Current | 800μA |
| Power Dissipation | 470mW |
| Max Supply Current | 1.5mA |
| Throw Configuration | SPST |
| Turn On Delay Time | 550 ns |
| Number of Inputs | 4 |
| Supply Type | Dual |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 340 ns |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 90Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 70 dB |
| Current - Leakage (IS(off)) (Max) | 5nA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 9pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 550ns, 340ns |
| Charge Injection | 20pC |
| Crosstalk | -90dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NC |
| Voltage - Supply, Dual (V±) | ±15V |
| Height | 3.81mm |
| Length | 21.33mm |
| Width | 7.11mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
DG221BDJ-E3 Overview
Due to its 16-DIP (0.300, 7.62mm) packaging, the electronic part is convenient for international shipping. High reliability is provided by advanced packaging method Tube. It is mounted in the position Through Hole. Multiplexers and demultiplexers have a ratio of 1:1. Around -40°C~85°C TA is the extended operating temperature. In total, 16 terminations have occurred. A high-quality output is provided by the electrical component's 1 channels. If the voltage supply is 15V volts, the electrical component should be turned on and run. It is injected into the electrical part body with 16 pins. The analog switch ics are built using SPST - NC switching circuits. Try searching for DG221 variants of the analog switch ic. Internally, this switch multiplexer has a resistance of 90Ohm. To find out what the 16 pins do, please refer to the datasheets. There is a standard Multiplexer or Switches analogue multiplexer here. normally, users should not supply switches with voltages higher than 18V. The analog switch ic is of the Dual supply type and is cost-effective. The lowest voltage the electronic part should receive is 13V. In order to operate this switch device, it would need a current of 800μA. The switch multiplexer may be damaged if it is exposed to voltage greater than 1.5mA. Despite this switch's dual supply capability, its voltage should not exceed 18V. In the case of dual power supplies, you should connect at least 7V. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them. The electrical part can be operated at 15V voltage levels. Among the inputs that can be operated are the 4 inputs.
DG221BDJ-E3 Features
1 Channels
Switch Circuit: SPST - NC
800μA Supply Current
DG221BDJ-E3 Applications
There are a lot of Vishay Siliconix DG221BDJ-E3 Analog Switches & Multiplexers ICs applications.
- Remote wireless modules
- RGB switches
- Medical
- Medical Instrumentation
- Fault Tolerant Systems
- Microprocessor controlled systems
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Digital cross connects (DSX-1)
- Microprocessor Controlled Analog Systems
- Industrial
