DG221BDY
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Weight | 547.485991mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Bulk |
| Published | 2009 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 90Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 600mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Reach Compliance Code | unknown |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| JESD-30 Code | R-PDSO-G16 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 15V |
| Number of Circuits | 4 |
| Max Supply Voltage | 18V |
| Min Supply Voltage | 13V |
| Max Supply Current | 1.5mA |
| Turn On Delay Time | 550 ns |
| Supply Type | Dual |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 340 ns |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 90Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 5nA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 9pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 550ns, 340ns |
| Charge Injection | 20pC |
| Crosstalk | -90dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NC |
| Voltage - Supply, Dual (V±) | ±15V |
| Height | 1.55mm |
| Length | 10mm |
| Width | 4mm |
| RoHS Status | Non-RoHS Compliant |
DG221BDY Overview
The electrical component comes in 16-SOIC (0.154, 3.90mm Width) packaging, which makes it convenient to ship overseas. This high-reliability packaging method uses advanced packaging methods Bulk. In Surface Mount, you'll find this switch device. Multiplexers and demultiplexers have the same number of circuits 1:1. The operating temperature is extended to around -40°C~85°C TA. The total number of terminations is 16. It is safe to turn on and run the electronic component with a 15V voltage supply. This electronic part can be found in the 16 series. These analog multiplexers are built based on SPST - NC switching circuits. A 4 circuit is present in this switch device. Internally, this switch multiplexer has a resistance of 90Ohm. Theswitch device is a typical Multiplexer or Switches. In normalcircumstances, users should not exceed 18V volts for the multiplexer. Dual supply type digital switch with a low cost. The lowest voltage the electronic part should receive is 13V. A digital multiplexer may suffer damage if voltage is applied above 1.5mA. If put voltage greater than 18V on the multiplexer, damage may be caused to the device. The voltage should be at least 7V if you are using dual power supplies. There are SEPARATE OUTPUT outputs on this analog switch ic. Operating voltages range from 15V.
DG221BDY Features
Switch Circuit: SPST - NC
DG221BDY Applications
There are a lot of Vishay Siliconix DG221BDY Analog Switches & Multiplexers ICs applications.
- Channelized and Unchannelized DS3 applications
- Microwave transmission systems
- PDH Multiplexers
- Microprocessor controlled systems
- DSLAMs
- Medical systems
- SDH/SONET multiplexers
- Multiplexers
- ATM
- Sample hold systems
