Parameters |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
5-TSSOP, SC-70-5, SOT-353 |
Number of Pins |
5 |
Weight |
19.986414mg |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2007 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
5 |
Resistance |
50Ohm |
Terminal Finish |
MATTE TIN |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
250mW |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
5V |
Time@Peak Reflow Temperature-Max (s) |
40 |
Base Part Number |
DG2302 |
Pin Count |
5 |
Power Supplies |
5V |
Number of Channels |
1 |
Number of Circuits |
1 |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
4V |
Operating Supply Current |
900μA |
Max Supply Current |
1.5mA |
Throw Configuration |
SPST |
Turn On Delay Time |
5 ns |
Supply Type |
Single |
Turn-Off Delay Time |
3.9 ns |
On-State Resistance (Max) |
7Ohm |
Multiplexer/Demultiplexer Circuit |
1:1 |
Current - Leakage (IS(off)) (Max) |
10μA |
Channel Capacitance (CS(off), CD(off)) |
5pF |
Switch Circuit |
SPST - NO |
Switch Time (Ton, Toff) (Max) |
5ns, 3.9ns |
Voltage - Supply, Single (V+) |
4V~5.5V |
Height |
1mm |
Length |
2mm |
Width |
1.25mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
DG2302DL-T1-E3 Overview
Due to its 5-TSSOP, SC-70-5, SOT-353 packaging, the electronic part is convenient for international shipping. Advanced packaging method Tape & Reel (TR) is used to provide high reliability. There is an analog multiplexer mounted in position Surface Mount. 1:1 is the ratio of multiplexer to demultiplexer circuits. Extended operating temperature around -40°C~85°C TA. There are 5 terminations totally. High-quality output is provided by the electronic component's 1 channels. If the voltage supply is 5V volts, the electrical component should be turned on and run. Electronic part bodies are injected with 5 pins. On the other hand, analog switches can be constructed using SPST - NO switching circuits. There are 1 circuits in this multiplexer. Try searching with DG2302 to find analog multiplexer variants. There is 50Ohm internal resistance in this digital multiplexer. The datasheets for the 5 pins explain the functions. The analog multiplexer shown here is a typical Multiplexer or Switches. In normalcircumstances, users should not exceed 5.5V volts for the multiplexer. An effective Single supply digital multiplexer. 4V is the lowest voltage the electrical component should receive. For this multiplexer to operate, 900μA current would be sufficient. An analogue multiplexer drains from a single voltage supply at 4V~5.5V. A voltage higher than 1.5mA may cause damage to the switch multiplexer.
DG2302DL-T1-E3 Features
1 Channels
Switch Circuit: SPST - NO
900μA Supply Current
DG2302DL-T1-E3 Applications
There are a lot of Vishay Siliconix DG2302DL-T1-E3 Analog Switches & Multiplexers ICs applications.
- DSLAMs
- RGB switches
- Switching Systems
- DVD-R
- Remote wireless modules
- Frame Relay Equipment
- Video switching
- Multiplexers
- Cross Connects
- SDH