DG2303DL-T1-E3
| Parameters | |
|---|---|
| Number of Terminations | 5 |
| Resistance | 15Ohm |
| Terminal Finish | MATTE TIN |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 250mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 1.8V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG2303 |
| Pin Count | 5 |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.65V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 1μA |
| Power Dissipation | 250mW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 4.4 ns |
| Number of Inputs | 1 |
| Supply Type | Single |
| Turn-Off Delay Time | 14.3 ns |
| On-State Resistance (Max) | 7Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 50 dB |
| Current - Leakage (IS(off)) (Max) | 10μA |
| Channel Capacitance (CS(off), CD(off)) | 9pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 2ns, 7.5ns |
| Charge Injection | 0.5pC |
| Voltage - Supply, Single (V+) | 1.65V~5.5V |
| Length | 2mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 5-TSSOP, SC-70-5, SOT-353 |
| Number of Pins | 5 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
DG2303DL-T1-E3 Overview
This electronic part is conveniently packaged in 5-TSSOP, SC-70-5, SOT-353, making it easy to ship abroad. The advanced packaging method Tape & Reel (TR) provides high reliability. Surface Mount is where this multiplexer is located. Multiplexers and demultiplexers have the same number of circuits 1:1. Increasing operating temperature to around -40°C~85°C TA. Total terminations are 5. Due to its 1 channels, the electrical component produces high-quality output. In the case of a voltage supply of 1.8V volts, the electrical part can be powered up and run. A total of 5 pins are injected into the electrical part body. These analog multiplexers are built based on SPST - NO switching circuits. Look for analog switch ic variants by searching with DG2303. Analog switches have 15Ohm internal resistance. To find out what the functions of 5 pins are, please refer to their datasheets. Multiplexer or Switches is a typical switch device. An abnormal situation would be for the switch device to be supplied with a voltage greater than 5.5V. An effective Single supply digital multiplexer. The lowest voltage fed to the electronic component should be 1.65V. This digital switch can be operated with a current of 1μA. The voltage required by this switch device is 1.65V~5.5V, draining from a single voltage supply. A digital multiplexer may suffer damage if voltage is applied above 1μA. There are 1 inputs to be operated.
DG2303DL-T1-E3 Features
1 Channels
Switch Circuit: SPST - NO
1μA Supply Current
DG2303DL-T1-E3 Applications
There are a lot of Vishay Siliconix DG2303DL-T1-E3 Analog Switches & Multiplexers ICs applications.
- Industrial control systems
- Multi-Line E1 Interface Cards
- RGB switches
- DVD-R
- Routers
- Cable Modem
- PDH Multiplexers
- Digital cross connects (DSX-1)
- Medical systems
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
