DG2512DN-T1-E4

35ns, 31ns SPST - NC 1.3Ohm DUAL Analog Switches BREAK-BEFORE-MAKE DG251* 6 Pins 2nA 3V 6-UFDFN

Manufacturer: Vishay Siliconix
Nocochips NO: 880-DG2512DN-T1-E4
Package: 6-UFDFN
Datasheet: PDF
Stock: 872
Description: 35ns, 31ns SPST - NC 1.3Ohm DUAL Analog Switches BREAK-BEFORE-MAKE DG251* 6 Pins 2nA 3V 6-UFDFN(Kg)

Details

Tags

Parameters
Width	1mm
RoHS Status	ROHS3 Compliant
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	6-UFDFN
Number of Pins	6
Weight	57.09594mg
Operating Temperature	-40°C~85°C TA
Packaging	Tape & Reel (TR)
Published	2016
JESD-609 Code	e4
Pbfree Code	yes
Part Status	Obsolete
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	6
Resistance	1.3Ohm
Terminal Finish	NICKEL PALLADIUM GOLD
Subcategory	Multiplexer or Switches
Max Power Dissipation	160mW
Technology	CMOS
Terminal Position	DUAL
Terminal Form	NO LEAD
Peak Reflow Temperature (Cel)	260
Number of Functions	1
Supply Voltage	3V
Terminal Pitch	0.4mm
Reach Compliance Code	unknown
Time@Peak Reflow Temperature-Max (s)	40
Base Part Number	DG251*
Pin Count	6
Qualification Status	Not Qualified
Power Supplies	3/5V
Number of Channels	1
Number of Circuits	1
Max Supply Voltage	5.5V
Min Supply Voltage	1.8V
Operating Supply Current	10nA
Max Supply Current	1μA
Throw Configuration	SPST
Turn On Delay Time	35 ns
Supply Type	Single
Turn-Off Delay Time	31 ns
On-State Resistance (Max)	1.3Ohm
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	58 dB
Current - Leakage (IS(off)) (Max)	2nA
Channel Capacitance (CS(off), CD(off))	19pF
On-state Resistance Match-Nom	0.15Ohm
Switch Circuit	SPST - NC
Switch Time (Ton, Toff) (Max)	35ns, 31ns
Charge Injection	14pC
Channel-to-Channel Matching (ΔRon)	150m Ω (Max)
Crosstalk	-64dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Switch-on Time-Max	49ns
Switch-off Time-Max	34ns
Voltage - Supply, Single (V+)	1.8V~5.5V
Normal Position	NC
Height	550μm
Length	1.2mm

DG2512DN-T1-E4 Overview

Presented in 6-UFDFN, this electrical component is convenient for overseas shipping. In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. Surface Mount is where this multiplexer is located. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Around -40°C~85°C TA is the extended operating temperature. There are 6 terminations totally. A 1 channel electronic part produces high-quality output. With a 3V voltage supply, the electrical component should be turned on and run. As part of the design of the 6 series, this electronic part has been incorporated into the system. These analog multiplexers are built based on SPST - NC switching circuits. It consists of 1 circuits. Try searching with DG251* if you're looking for variants. There is 1.3Ohm internal resistance in this digital multiplexer. The datasheets for the 6 pins explain the functions. It is a typical Multiplexer or Switches analog multiplexer. Users shouldn't supply more than 5.5V voltage to the switch device. The analog switch ic is of the Single supply type and is cost-effective. In order for the electronic part to function properly, the lowest voltage should be 1.8V. In order to operate this switch device, it would need a current of 10nA. The voltage required by this switch device is 1.8V~5.5V, draining from a single voltage supply. The analogue multiplexer may be damaged if voltage is greater than 1μA.