DG2513DN-T1-E4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 6-UFDFN |
| Number of Pins | 6 |
| Weight | 57.09594mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| Resistance | 1.3Ohm |
| Terminal Finish | NICKEL PALLADIUM GOLD |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 160mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.4mm |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG251* |
| Pin Count | 6 |
| Qualification Status | Not Qualified |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 10nA |
| Power Dissipation | 160mW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 35 ns |
| Number of Inputs | 1 |
| Supply Type | Single |
| Turn-Off Delay Time | 31 ns |
| On-State Resistance (Max) | 1.3Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 58 dB |
| Current - Leakage (IS(off)) (Max) | 2nA |
| Channel Capacitance (CS(off), CD(off)) | 19pF |
| On-state Resistance Match-Nom | 0.15Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 35ns, 31ns |
| Charge Injection | 14pC |
| Channel-to-Channel Matching (ΔRon) | 150m Ω (Max) |
| Crosstalk | -64dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 49ns |
| Switch-off Time-Max | 34ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Normal Position | NO |
| Height | 550μm |
| Length | 1.2mm |
| Width | 1mm |
| RoHS Status | ROHS3 Compliant |
DG2513DN-T1-E4 Overview
The electrical component comes in 6-UFDFN packaging, which makes it convenient to ship overseas. This packaging method provides high reliability because it uses advanced packaging techniques. This analog switch is mounted in Surface Mount. There is 1:1 ratio between the number of multiplexers and demultiplexers. Extended operating temperature around -40°C~85°C TA. In total, there have been 6 terminations. High-quality output is provided by the electronic component's 1 channels. Powered by a 3V voltage supply, the electrical part should be switched on and run. An injection of 6 pins is performed into the body of the electrical component. Unlike digital switches, these are based on SPST - NO switching circuits. Try searching with DG251* to find analog multiplexer variants. A 1.3Ohm internal resistance characterizes this multiplexer. To find out what the 6 pins do, please refer to the datasheets. It is a typical Multiplexer or Switches analog multiplexer. Users shouldn't supply more than 5.5V voltage to the switch device. Analogue multiplexers of the Single supply type that are cost-effective. 1.8V should be the lowest voltage fed to the electronic component. For this digital switch to work, 10nA current would suffice. A voltage of 1.8V~5.5V is required to drain this analog switch from a single voltage supply. A voltage higher than 1μA may cause damage to the switch multiplexer. Among the inputs that can be operated are the 1 inputs.
DG2513DN-T1-E4 Features
1 Channels
Switch Circuit: SPST - NO
10nA Supply Current
DG2513DN-T1-E4 Applications
There are a lot of Vishay Siliconix DG2513DN-T1-E4 Analog Switches & Multiplexers ICs applications.
- Battery-powered systems
- Mechanical reed relay replacement
- High-Voltage
- RGB switches
- T1/E1 Terminals
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- CSU
- Medical systems
- Residential Gateways, Home Gateway/Router
- SDH
