Parameters |
Time@Peak Reflow Temperature-Max (s) |
40 |
Base Part Number |
DG2515 |
Pin Count |
10 |
Number of Outputs |
4 |
Qualification Status |
Not Qualified |
Power Supplies |
3/5V |
Number of Channels |
1 |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
1.8V |
Operating Supply Current |
10nA |
Nominal Supply Current |
10nA |
Power Dissipation |
320mW |
Max Supply Current |
1μA |
Turn On Delay Time |
70 ns |
Number of Inputs |
2 |
Supply Type |
Single |
Turn-Off Delay Time |
50 ns |
-3db Bandwidth |
235MHz |
On-State Resistance (Max) |
4Ohm |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
51 dB |
Current - Leakage (IS(off)) (Max) |
1nA |
Channel Capacitance (CS(off), CD(off)) |
17pF |
On-state Resistance Match-Nom |
0.1Ohm |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
50ns, 40ns |
Charge Injection |
49pC |
Channel-to-Channel Matching (ΔRon) |
100m Ω |
Crosstalk |
-74dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Voltage - Supply, Single (V+) |
1.8V~5.5V |
Height Seated (Max) |
1.1mm |
Length |
3mm |
RoHS Status |
ROHS3 Compliant |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
10-TFSOP, 10-MSOP (0.118, 3.00mm Width) |
Number of Pins |
10 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2015 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
10 |
Resistance |
4Ohm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
320mW |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
2 |
Supply Voltage |
3V |
Terminal Pitch |
0.5mm |
DG2515DQ-T1-E3 Overview
The electrical component comes in 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) packaging, which makes it convenient to ship overseas. Advanced packaging method Tape & Reel (TR) is used to provide high reliability. In Surface Mount, this analog switch is mounted. 2:1 is the ratio of multiplexer to demultiplexer circuits. Extended operating temperature around -40°C~85°C TA. In total, there have been 10 terminations. A high-quality output is provided by the electrical component's 1 channels. It is safe to turn on and run the electronic component with a 3V voltage supply. A key feature of the 10 series is the inclusion of this electronic part as part of its design. A SPDT switching circuit is used for these analog switches. Try searching with DG2515 to find analog multiplexer variants. There is 4Ohm internal resistance in this digital multiplexer. Datasheets for 10 pin functions are available upon request. A analogue multiplexer of this type is a Multiplexer or Switches. normally, users should not supply switches with voltages higher than 5.5V. The analog switch ic is of the Single supply type and is cost-effective. 1.8V is the lowest voltage that should be fed to the electronic electronic part. For this multiplexer to operate, 10nA current would be sufficient. Using a single voltage supply, this switch device consumes 1.8V~5.5V volts. It may damage the digital multiplexer if the voltage is higher than 1μA. Among the inputs that can be operated are the 2 inputs. There are 4 outputs on the analogue multiplexer.
DG2515DQ-T1-E3 Features
1 Channels
Switch Circuit: SPDT
10nA Supply Current
-3db Bandwidth: 235MHz
DG2515DQ-T1-E3 Applications
There are a lot of Vishay Siliconix DG2515DQ-T1-E3 Analog Switches & Multiplexers ICs applications.
- DSUs
- Private Branch Exchange (PBX)
- Frame Relay Equipment
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- FTTH
- Sample-and-hold systems
- Audio and video switching
- Cellular phones
- CSU
- Cable PC