Parameters |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
10-TFSOP, 10-MSOP (0.118, 3.00mm Width) |
Number of Pins |
10 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2013 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
10 |
Resistance |
4Ohm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
320mW |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
2 |
Supply Voltage |
3V |
Terminal Pitch |
0.5mm |
Reach Compliance Code |
unknown |
Time@Peak Reflow Temperature-Max (s) |
40 |
Base Part Number |
DG2516 |
Output |
SEPARATE OUTPUT |
Pin Count |
10 |
Qualification Status |
Not Qualified |
Power Supplies |
3/5V |
Number of Channels |
1 |
Number of Circuits |
2 |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
1.8V |
Operating Supply Current |
10nA |
Nominal Supply Current |
10nA |
Max Supply Current |
1μA |
Turn On Delay Time |
70 ns |
Supply Type |
Single |
Turn-Off Delay Time |
50 ns |
-3db Bandwidth |
235MHz |
On-State Resistance (Max) |
4Ohm |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
51 dB |
Current - Leakage (IS(off)) (Max) |
1nA |
Channel Capacitance (CS(off), CD(off)) |
17pF |
On-state Resistance Match-Nom |
0.1Ohm |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
50ns, 40ns |
Charge Injection |
49pC |
Channel-to-Channel Matching (ΔRon) |
100m Ω |
Crosstalk |
-74dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Voltage - Supply, Single (V+) |
1.8V~5.5V |
Height Seated (Max) |
1.1mm |
Length |
3mm |
RoHS Status |
ROHS3 Compliant |
DG2516DQ-T1-E3 Overview
The electrical component comes in 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) packaging, which makes it convenient to ship overseas. To ensure high reliability, a new packaging method Tape & Reel (TR) is used. In Surface Mount, this analog switch is mounted. In the multiplexer and demultiplexer, 2:1 represents the number of circuits. Operational temperature extended around -40°C~85°C TA. Total terminations are 10. By its 1 channels, the electronic component provides high-quality output. When the electronic component is given a voltage of 3V, it should be turned on and run. This electronic part can be found in the 10 series. SPDT switching circuits are used in these analog switch ics. There are 2 circuits in this multiplexer. Try searching for the analog switch ic with DG2516 if you are looking for variants. This digital multiplexer has 4Ohm internal resistance. For functions related to 10 pins, please refer to the datasheets. It is a typical Multiplexer or Switches analog multiplexer. In normalcircumstances, users should not exceed 5.5V volts for the multiplexer. A cost-effective Single supply type analogue multiplexer. It is recommended to use 1.8V as the lowest voltage for the electrical part. An operating current of 10nA would be sufficient for this switch device. Analogue multiplexers require a 1.8V~5.5V voltage to drain from a single voltage supply. It may damage the digital multiplexer if the voltage is higher than 1μA. The digital multiplexer has SEPARATE OUTPUT outputs that can be used.
DG2516DQ-T1-E3 Features
1 Channels
Switch Circuit: SPDT
10nA Supply Current
-3db Bandwidth: 235MHz
DG2516DQ-T1-E3 Applications
There are a lot of Vishay Siliconix DG2516DQ-T1-E3 Analog Switches & Multiplexers ICs applications.
- Audio and video routing
- Video signal routing
- E1 Multiplexer
- Medical Instrumentation
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Imaging
- Medical
- DSUs
- Microprocessor controlled systems
- Microwave transmission systems