DG2517DN-T1-E4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 10-VFDFN Exposed Pad |
| Number of Pins | 10 |
| Weight | 50.008559mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2015 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Resistance | 4Ohm |
| Max Power Dissipation | 1.191W |
| Reach Compliance Code | unknown |
| Base Part Number | DG2517 |
| Pin Count | 10 |
| Number of Outputs | 4 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 10nA |
| Power Dissipation | 1.191W |
| Max Supply Current | 1μA |
| Turn On Delay Time | 25 ns |
| Number of Inputs | 2 |
| Supply Type | Single |
| Turn-Off Delay Time | 20 ns |
| -3db Bandwidth | 242MHz |
| On-State Resistance (Max) | 4Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 8pF |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 25ns, 20ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 100m Ω |
| Crosstalk | -73dB @ 1MHz |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Height | 880μm |
| Length | 3mm |
| Width | 3mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
DG2517DN-T1-E4 Overview
The electronic component is convenient to ship overseas because it is packed in a 10-VFDFN Exposed Pad. The advanced packaging method Tape & Reel (TR) provides high reliability. In Surface Mount, you'll find this switch device. In the multiplexer and demultiplexer, 2:1 represents the number of circuits. An extended operating temperature of -40°C~85°C TA degrees Celsius. An injection of 10 pins is performed into the body of the electrical component. The analog switch ics are built using SPDT switching circuits. Try searching for the analog switch ic with DG2517 if you are looking for variants. This digital multiplexer has 4Ohm internal resistance. Datasheets for 10 pin functions are available upon request. In a normalsituation, users should not supply the switches with voltage higher than 5.5V. The digital multiplexer has a low cost Single supply. It is recommended that the electrical component receives a voltage of 1.8V. This multiplexer would work with 10nA current. An analogue multiplexer drains from a single voltage supply at 1.8V~5.5V. Put voltage above 1μA on the multiplexer to cause damage. Operating 2 inputs is required. This digital multiplexer has 4 outputs.
DG2517DN-T1-E4 Features
Switch Circuit: SPDT
10nA Supply Current
-3db Bandwidth: 242MHz
DG2517DN-T1-E4 Applications
There are a lot of Vishay Siliconix DG2517DN-T1-E4 Analog Switches & Multiplexers ICs applications.
- PDH Multiplexers
- High speed data transmission line cards
- Audio and video switching
- Data Acquisition Systems
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Multiplexers
- SONET/SDH ADM
- Relay Replacement
- Audio and video signal routing
- PDAs
