DG2531DQ-T1-E3
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 10 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| Resistance | 600mOhm |
| Terminal Finish | MATTE TIN |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 320mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.5mm |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG2531 |
| Pin Count | 10 |
| Number of Outputs | 4 |
| Qualification Status | Not Qualified |
| Power Supplies | 3V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 1μA |
| Power Dissipation | 320mW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 70 ns |
| Number of Inputs | 2 |
| Supply Type | Single |
| Turn-Off Delay Time | 65 ns |
| On-State Resistance (Max) | 600mOhm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 69 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 143pF |
| On-state Resistance Match-Nom | 0.05Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 70ns, 65ns |
| Charge Injection | 54pC |
| Channel-to-Channel Matching (ΔRon) | 50m Ω (Max) |
| Crosstalk | -69dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 77ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Height Seated (Max) | 1.1mm |
| Length | 3mm |
| Width | 3mm |
| RoHS Status | ROHS3 Compliant |
DG2531DQ-T1-E3 Overview
Packed in 10-TFSOP, 10-MSOP (0.118, 3.00mm Width), the electronic component is convenient for shipping overseas. Advanced packaging method Tape & Reel (TR) is used to provide high reliability. This analog switch is mounted in Surface Mount. In the multiplexer and demultiplexer, 2:1 represents the number of circuits. Operational temperature extended around -40°C~85°C TA. In total, there are 10 terminations. By its 1 channels, the electronic component provides high-quality output. If the voltage supply is 3V volts, the electrical component should be turned on and run. 10 pins are injected to the electronic part body. These analog multiplexers are built based on SPDT switching circuits. Using the DG2531 search parameter, you can discover variants of the switch. A 600mOhm internal resistance characterizes this multiplexer. The functions of 10 pins can be found in the datasheets. This switch device is a typical Multiplexer or Switches. Users shouldn't supply more than 5.5V voltage to the switch device. A cost-effective Single supply type analogue multiplexer. A low voltage of 1.8V should be applied to the electronic component. For this digital switch to work, 1μA current would suffice. Using only a single voltage supply, this analog switch requires 1.8V~5.5V voltage. Putting voltage greater than 1μA on the multiplexer may cause damage. There are 2 inputs to be operated. In this digital multiplexer, there are 4 outputs.
DG2531DQ-T1-E3 Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
DG2531DQ-T1-E3 Applications
There are a lot of Vishay Siliconix DG2531DQ-T1-E3 Analog Switches & Multiplexers ICs applications.
- Fault Tolerant Systems
- Precision instrumentation
- Multi-Line E1 Interface Cards
- SDH
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Ultrasound
- Cell phones
- Data Acquisition Systems
- RGB switches
- High reliability control systems
