DG2532DQ-T1-E3
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 10 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| Resistance | 600mOhm |
| Terminal Finish | MATTE TIN |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 320mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG2532 |
| Pin Count | 10 |
| Number of Outputs | 4 |
| Qualification Status | Not Qualified |
| Power Supplies | 3V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 1μA |
| Power Dissipation | 320mW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 70 ns |
| Number of Inputs | 2 |
| Supply Type | Single |
| Turn-Off Delay Time | 65 ns |
| On-State Resistance (Max) | 600mOhm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 69 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 143pF |
| On-state Resistance Match-Nom | 0.05Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 70ns, 65ns |
| Charge Injection | 54pC |
| Channel-to-Channel Matching (ΔRon) | 50m Ω (Max) |
| Crosstalk | -69dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 77ns |
| Voltage - Supply, Single (V+) | 1.8V~5.5V |
| Height Seated (Max) | 1.1mm |
| Length | 3mm |
| Width | 3mm |
| RoHS Status | ROHS3 Compliant |
DG2532DQ-T1-E3 Overview
Shipping overseas is convenient with the electronic component packed in 10-TFSOP, 10-MSOP (0.118, 3.00mm Width). High reliability is achieved by using advanced packaging method Tape & Reel (TR). Mounted in Surface Mount is this multiplexer. 2:1 is the ratio between multiplexers and demultiplexers. Extended operating temperature around -40°C~85°C TA. The total number of terminations is 10. A 1 channel electronic part produces high-quality output. An 3V voltage supply should allow the electrical part to be turned on and run. Into the electrical component body are injected 10 pins. A SPDT switching circuit is used to build these analog multiplexers. Look for analog switch ic variants by searching with DG2532. Analog switches have 600mOhm internal resistance. Datasheets for functions of 10 pins are available. In this analog multiplexer, the value is Multiplexer or Switches. normally, users should not supply switches with voltages higher than 5.5V. The analog switch ic is of the Single supply type and is cost-effective. 1.8V is the lowest voltage that should be fed to the electronic electronic part. For this digital switch to work, 1μA current would suffice. Using a single voltage supply, this switch device consumes 1.8V~5.5V volts. If put voltage greater than 1μA on the device, damage may be caused to the analogue multiplexer. It is possible to operate 2 inputs. The analogue multiplexer has 4 outputs.
DG2532DQ-T1-E3 Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
DG2532DQ-T1-E3 Applications
There are a lot of Vishay Siliconix DG2532DQ-T1-E3 Analog Switches & Multiplexers ICs applications.
- Fiber In The Loop (FITL)
- Battery Powered Instruments
- Data Acquisition Systems
- Avionics
- Digital cross connects (DSX-1)
- DSUs
- DVD-R
- Industrial and process control systems
- Microprocessor Controlled Analog Systems
- Cell phones
