DG2535DN-T1-E4
| Parameters | |
|---|---|
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.5mm |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG2535 |
| Pin Count | 10 |
| Number of Outputs | 4 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 3V |
| Power Supplies | 3V |
| Number of Channels | 1 |
| Max Supply Voltage | 6V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 1μA |
| Power Dissipation | 1.191W |
| Max Supply Current | 1μA |
| Turn On Delay Time | 82 ns |
| Number of Inputs | 2 |
| Supply Type | Single |
| Turn-Off Delay Time | 73 ns |
| On-State Resistance (Max) | 500mOhm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 69 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 145pF |
| On-state Resistance Match-Nom | 0.05Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 82ns, 73ns |
| Charge Injection | 21pC |
| Channel-to-Channel Matching (ΔRon) | 50m Ω (Max) |
| Crosstalk | -69dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 90ns |
| Switch-off Time-Max | 78ns |
| Normal Position | NO/NC |
| Height | 880μm |
| Length | 3mm |
| Width | 3mm |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 10-VFDFN Exposed Pad |
| Number of Pins | 10 |
| Weight | 50.008559mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| Resistance | 500mOhm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 1.191W |
| Technology | CMOS |
| Terminal Position | QUAD |
DG2535DN-T1-E4 Overview
Due to its 10-VFDFN Exposed Pad packaging, the electronic part is convenient for international shipping. High reliability is achieved by using advanced packaging method Tape & Reel (TR). Multiplexers like this are mounted in the Surface Mount position. 2:1 is the ratio of multiplexer to demultiplexer circuits. Temperatures around -40°C~85°C TA are extended for operation. Total terminations are 10. High-quality output is provided by the electronic component's 1 channels. When a voltage supply of 3V is used, the electronic component should be turned on and run. Electronic part bodies are injected with 10 pins. Unlike digital switches, these are based on SPDT switching circuits. Try searching for DG2535 variants of the analog switch ic. There is 500mOhm internal resistance in this digital multiplexer. For functions related to 10 pins, please refer to the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. A voltage higher than 6V should not normally be supplied to the switches. Analog switch ics with Single supply type are cost-effective. 1.8V should be the lowest voltage fed to the electronic component. An operating current of 1μA would be sufficient for this switch device. When the digital multiplexer is charged above 1μA, damage can occur. It can operate from 3V operating voltages. In order to operate the 2 inputs, there are several steps to follow. Multiplexer ics with 4 outputs are available.
DG2535DN-T1-E4 Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
DG2535DN-T1-E4 Applications
There are a lot of Vishay Siliconix DG2535DN-T1-E4 Analog Switches & Multiplexers ICs applications.
- SDH
- Communications systems
- Audio signal routing
- Wireless Local Loop
- Audio/video switches
- Public switching systems
- Channel Banks
- Frame Relay Equipment
- DSLAMs
- USB 1.1 signal switching circuits
