DG2539DQ-T1-GE3

30ns, 35ns SPST - NO/NC 4.5Ohm Analog Switches BREAK-BEFORE-MAKE DG2539 10 Pins 250pA 3V 10-TFSOP, 10-MSOP (0.118, 3.00mm Width)

Manufacturer: Vishay Siliconix
Nocochips NO: 880-DG2539DQ-T1-GE3
Package: 10-TFSOP, 10-MSOP (0.118, 3.00mm Width)
Datasheet: PDF
Stock: 217
Description: 30ns, 35ns SPST - NO/NC 4.5Ohm Analog Switches BREAK-BEFORE-MAKE DG2539 10 Pins 250pA 3V 10-TFSOP, 10-MSOP (0.118, 3.00mm Width)(Kg)

Inquiry Now

Details

Tags

Parameters
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	10-TFSOP, 10-MSOP (0.118, 3.00mm Width)
Number of Pins	10
Weight	143.193441mg
Operating Temperature	-40°C~85°C TA
Packaging	Tape & Reel (TR)
Published	2013
Part Status	Obsolete
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	10
Resistance	4.5Ohm
Subcategory	Multiplexer or Switches
Max Power Dissipation	320mW
Technology	CMOS
Terminal Form	GULL WING
Number of Functions	2
Supply Voltage	3V
Terminal Pitch	0.5mm
Base Part Number	DG2539
Output	SEPARATE OUTPUT
Pin Count	10
Number of Channels	1
Number of Circuits	2
Max Supply Voltage	4.3V
Min Supply Voltage	1.25V
Operating Supply Current	2μA
Max Supply Current	2μA
Throw Configuration	SPST
Turn On Delay Time	35 ns
Voltage - Supply, Single/Dual (±)	2.6V~4.3V ±2.5V
Supply Type	Dual, Single
Turn-Off Delay Time	20 ns
Max Dual Supply Voltage	2.75V
-3db Bandwidth	366MHz
On-State Resistance (Max)	4.5Ohm
Min Dual Supply Voltage	1.25V
Dual Supply Voltage	2.5V
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	67 dB
Current - Leakage (IS(off)) (Max)	250pA
Channel Capacitance (CS(off), CD(off))	8pF 9pF
On-state Resistance Match-Nom	0.3Ohm
Switch Circuit	SPST - NO/NC
Switch Time (Ton, Toff) (Max)	30ns, 35ns
Charge Injection	2.2pC
Channel-to-Channel Matching (ΔRon)	200m Ω
Crosstalk	-90dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Switch-on Time-Max	55ns
Switch-off Time-Max	40ns
Height	950μm
Length	3mm
Width	3.1mm
Radiation Hardening	No
REACH SVHC	Unknown
RoHS Status	ROHS3 Compliant

DG2539DQ-T1-GE3 Overview

Shipping overseas is convenient with the electronic component packed in 10-TFSOP, 10-MSOP (0.118, 3.00mm Width). The advanced packaging method Tape & Reel (TR) provides high reliability. Multiplexers like this are mounted in the Surface Mount position. 1:1 is the ratio between multiplexers and demultiplexers. Extended operating temperature around -40°C~85°C TA. A total of 10 terminations have been recorded. By its 1 channels, the electronic component provides high-quality output. Powered by a 3V voltage supply, the electrical part should be switched on and run. Electronic part bodies are injected with 10 pins. Multiplexers built on a SPST - NO/NC switching circuit are built. This multiplexer is composed of 2 circuits. Use DG2539 to search for variants of the digital switches. The internal resistance of this digital multiplexer is 4.5Ohm. For details about the functions of 10 pins, please refer to the datasheets. Multiplexer or Switches is a typical switch device. It is normally recommended that users do not supply the multiplexer with voltages higher than 4.3V. Analogue multiplexer with a Dual, Single supply type that is cost-effective. In order for the electronic part to function properly, the lowest voltage should be 1.25V. The switch device would be able to operate with 2μA current. Putting voltage greater than 2μA on the multiplexer may cause damage. For this switch, a dual supply voltage is feasible, but it must not exceed 2.75VThe voltage should be at least 1.25V if you are using dual power supplies. In this switch multiplexer, there are SEPARATE OUTPUT outputs available.