DG2599DN-T1-GE4
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-WFQFN |
| Number of Pins | 16 |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 1.1Ohm |
| Terminal Finish | NICKEL PALLADIUM GOLD |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 525mW |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG2599 |
| Pin Count | 16 |
| Number of Outputs | 8 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 3V |
| Power Supplies | 3V |
| Temperature Grade | INDUSTRIAL |
| Number of Channels | 2 |
| Number of Circuits | 2 |
| Max Supply Voltage | 5V |
| Min Supply Voltage | 1.65V |
| Operating Supply Current | 1nA |
| Nominal Supply Current | 1nA |
| Power Dissipation | 525mW |
| Turn On Delay Time | 115 ns |
| Number of Inputs | 4 |
| Supply Type | Single |
| Turn-Off Delay Time | 85 ns |
| -3db Bandwidth | 186MHz |
| On-State Resistance (Max) | 1.1Ohm |
| Multiplexer/Demultiplexer Circuit | 2:2 |
| Off-state Isolation-Nom | 66 dB |
| Current - Leakage (IS(off)) (Max) | 10nA |
| Channel Capacitance (CS(off), CD(off)) | 9pF |
| Switch Circuit | DPDT |
| Switch Time (Ton, Toff) (Max) | 90ns, 70ns |
| Charge Injection | 10pC |
| Crosstalk | -110dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.65V~5V |
| RoHS Status | ROHS3 Compliant |
DG2599DN-T1-GE4 Overview
Packed in 16-WFQFN, the electronic component is convenient for shipping overseas. To ensure high reliability, a new packaging method Tape & Reel (TR) is used. It is mounted in the position Surface Mount. Multiplexers and demultiplexers have the same number of circuits 2:2. Totally, there are 16 terminations. The electronic part delivers high-quality output through its 2 channels. In the case of a voltage supply of 3V volts, the electrical part can be powered up and run. It is part of the design of the 16 series that this electronic component is included. A DPDT switching circuit is used for these analog switches. A total of 2 circuits make up this switch device. Try searching with DG2599 if you're looking for variants. Internally, this switch multiplexer has a resistance of 1.1Ohm. The datasheets for the 16 pins explain the functions. Multiplexer or Switches is a typical switch device. It is generally not recommended to supply a voltage higher than 5V to the switch device in normal circumstances. The analog switch ic is of the Single supply type and is cost-effective. 1.65V is the lowest voltage the electrical component should receive. An operating current of 1nA would be sufficient for this switch device. Draining from a single voltage supply, this analog switch requires a voltage of 1.65V~5V. Operating voltages range from 3V. There are 4 inputs to be operated. There are 8 outputs on the analogue multiplexer.
DG2599DN-T1-GE4 Features
2 Channels
Switch Circuit: DPDT
1nA Supply Current
-3db Bandwidth: 186MHz
DG2599DN-T1-GE4 Applications
There are a lot of Vishay Siliconix DG2599DN-T1-GE4 Analog Switches & Multiplexers ICs applications.
- Data switching
- Cell phones
- Cellular phones
- Voice over IP/DSL – Integrated Access Devices, Smart
- Mechanical reed relay replacement
- Low-Voltage
- Battery Powered Instruments
- Private Branch Exchange (PBX)
- Isolation
- Audio and video routing
