banner_page

DG2612DX-T1-E3

60ns, 35ns SPDT 1.4Ohm DUAL Analog Switches BREAK-BEFORE-MAKE DG2612 6 Pins 2nA 3V SOT-563, SOT-666


  • Manufacturer: Vishay Siliconix
  • Nocochips NO: 880-DG2612DX-T1-E3
  • Package: SOT-563, SOT-666
  • Datasheet: PDF
  • Stock: 317
  • Description: 60ns, 35ns SPDT 1.4Ohm DUAL Analog Switches BREAK-BEFORE-MAKE DG2612 6 Pins 2nA 3V SOT-563, SOT-666(Kg)

Details

Tags

Parameters
Mount Surface Mount
Mounting Type Surface Mount
Package / Case SOT-563, SOT-666
Weight 32.006612mg
Operating Temperature -40°C~85°C TA
Packaging Tape & Reel (TR)
Published 2008
JESD-609 Code e3
Pbfree Code yes
Part Status Obsolete
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 6
Resistance 1.4Ohm
Terminal Finish MATTE TIN
Subcategory Multiplexer or Switches
Max Power Dissipation 172mW
Technology CMOS
Terminal Position DUAL
Terminal Form FLAT
Peak Reflow Temperature (Cel) 260
Number of Functions 1
Supply Voltage 3V
Terminal Pitch 0.5mm
Reach Compliance Code unknown
Time@Peak Reflow Temperature-Max (s) 40
Base Part Number DG2612
Output SEPARATE OUTPUT
Pin Count 6
JESD-30 Code R-PDSO-F6
Qualification Status Not Qualified
Power Supplies 3V
Number of Channels 1
Number of Circuits 1
Max Supply Voltage 5.5V
Min Supply Voltage 1.8V
Operating Supply Current 10nA
Max Supply Current 1μA
Turn On Delay Time 60 ns
Supply Type Single
Turn-Off Delay Time 35 ns
On-State Resistance (Max) 1.4Ohm
Multiplexer/Demultiplexer Circuit 2:1
Off-state Isolation-Nom 67 dB
Current - Leakage (IS(off)) (Max) 2nA
Channel Capacitance (CS(off), CD(off)) 36pF
On-state Resistance Match-Nom 0.1Ohm
Switch Circuit SPDT
Switch Time (Ton, Toff) (Max) 60ns, 35ns
Charge Injection 2.4pC
Channel-to-Channel Matching (ΔRon) 100m Ω (Max)
Crosstalk -73dB @ 100kHz
Switching BREAK-BEFORE-MAKE
Switch-on Time-Max 63ns
Switch-off Time-Max 37ns
Voltage - Supply, Single (V+) 1.8V~5.5V
Normal Position NC
Height 600μm
Length 1.7mm
Width 1.2mm
RoHS Status ROHS3 Compliant

DG2612DX-T1-E3 Overview


Due to its SOT-563, SOT-666 packaging, the electronic part is convenient for international shipping. A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). A switch device like this is mounted in Surface Mount. Multiplexers and demultiplexers have a ratio of 2:1. Temperatures around -40°C~85°C TA are extended for operation. Total terminations are 6. As a result of its 1 channels, this electronic component provides high-quality output. When the electronic component is given a voltage of 3V, it should be turned on and run. The electronic part body is injected with 6 pins. A SPDT switching circuit is used for these analog switches. It consists of 1 circuits. Try searching with DG2612 if you're looking for variants. As far as internal resistance is concerned, it has 1.4Ohm. There is a standard Multiplexer or Switches analogue multiplexer here. normally, users should not supply switches with voltages higher than 5.5V. An effective Single supply digital multiplexer. 1.8V is the lowest voltage that should be fed to the electronic electronic part. An operating current of 10nA would be sufficient for this switch device. A voltage of 1.8V~5.5V is required for this switch device, which drains from a single voltage source. If put voltage greater than 1μA on the device, damage may be caused to the analogue multiplexer. The analog switch ic utilizes SEPARATE OUTPUT outputs in total.

DG2612DX-T1-E3 Features


1 Channels
Switch Circuit: SPDT
10nA Supply Current

DG2612DX-T1-E3 Applications


There are a lot of Vishay Siliconix DG2612DX-T1-E3 Analog Switches & Multiplexers ICs applications.

  • Cable PC
  • Multi-Line E1 Interface Cards
  • Power routing
  • 65 V DACs
  • ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
  • Mechanical reed relay replacement
  • SDH
  • Ultrasound
  • Digital cross connects (DSX-1)
  • Video signal routing

Write a review

Note: HTML is not translated!
    Bad           Good