DG2616DN-T1-E4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 10-VFDFN Exposed Pad |
| Number of Pins | 10 |
| Weight | 50.008559mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| Resistance | 7Ohm |
| Terminal Finish | NICKEL PALLADIUM GOLD |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 1.191W |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.5mm |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG2616 |
| Pin Count | 10 |
| Number of Outputs | 4 |
| Qualification Status | Not Qualified |
| Power Supplies | 3V |
| Number of Channels | 1 |
| Max Supply Voltage | 3.6V |
| Min Supply Voltage | 1.5V |
| Operating Supply Current | 100nA |
| Power Dissipation | 1.191W |
| Max Supply Current | 300μA |
| Turn On Delay Time | 69 ns |
| Number of Inputs | 2 |
| Supply Type | Single |
| Turn-Off Delay Time | 39 ns |
| On-State Resistance (Max) | 7Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 32 dB |
| Current - Leakage (IS(off)) (Max) | 2nA |
| Channel Capacitance (CS(off), CD(off)) | 9pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 69ns, 39ns |
| Charge Injection | 7pC |
| Channel-to-Channel Matching (ΔRon) | 100m Ω |
| Crosstalk | -80dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 76ns |
| Voltage - Supply, Single (V+) | 1.5V~3.6V |
| Drain to Source Resistance | 4.2Ohm |
| Height | 880μm |
| Length | 3mm |
| Width | 3mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
DG2616DN-T1-E4 Overview
Packed in 10-VFDFN Exposed Pad, the electronic component is convenient for shipping overseas. A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). Mounted in Surface Mount is this multiplexer. There is 2:1 ratio between the number of multiplexers and demultiplexers. Extended operating temperature around -40°C~85°C TA. Total terminations are 10. As a result of its 1 channels, this electronic component provides high-quality output. When the electronic component is given a voltage of 3V, it should be turned on and run. A total of 10 pins are injected into the electrical part body. Multiplexers built on a SPDT switching circuit are built. Using the DG2616 search parameter, you can discover variants of the switch. As far as internal resistance is concerned, it has 7Ohm. To find out what the 10 pins do, please refer to the datasheets. A analogue multiplexer of this type is a Multiplexer or Switches. Users shouldn't supply more than 3.6V voltage to the switch device. Analogue multiplexer with a Single supply type that is cost-effective. 1.5V should be the lowest voltage fed to the electronic component. This digital switch can be operated with a current of 100nA. An analogue multiplexer drains from a single voltage supply at 1.5V~3.6V. Putting voltage greater than 300μA on the multiplexer may cause damage. Operating 2 inputs is required. This electronic component presents a Drain to Source resistance of 4.2Ohm. A analog switch ics with 4 outputs is included.
DG2616DN-T1-E4 Features
1 Channels
Switch Circuit: SPDT
100nA Supply Current
Drain-to-Source resistance: 4.2Ohm
DG2616DN-T1-E4 Applications
There are a lot of Vishay Siliconix DG2616DN-T1-E4 Analog Switches & Multiplexers ICs applications.
- Microwave transmission systems
- PBX interfaces
- Data Acquisition Systems
- MP3 players
- HDTV
- Cable PC
- Data switching
- Routers
- Channelized and Unchannelized DS3 applications
- Modems
