DG2617DN-T1-E4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 10-VFDFN Exposed Pad |
| Number of Pins | 10 |
| Weight | 50.008559mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2016 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| Resistance | 7Ohm |
| Terminal Finish | NICKEL PALLADIUM GOLD |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 1.191W |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.5mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG2617 |
| Pin Count | 10 |
| Number of Outputs | 4 |
| Qualification Status | Not Qualified |
| Power Supplies | 3V |
| Number of Channels | 1 |
| Max Supply Voltage | 3.6V |
| Min Supply Voltage | 1.5V |
| Operating Supply Current | 100nA |
| Power Dissipation | 1.191W |
| Max Supply Current | 300μA |
| Turn On Delay Time | 69 ns |
| Number of Inputs | 2 |
| Supply Type | Single |
| Turn-Off Delay Time | 39 ns |
| On-State Resistance (Max) | 7Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 32 dB |
| Current - Leakage (IS(off)) (Max) | 2nA |
| Channel Capacitance (CS(off), CD(off)) | 9pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 69ns, 39ns |
| Charge Injection | 7pC |
| Channel-to-Channel Matching (ΔRon) | 100m Ω |
| Crosstalk | -80dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 76ns |
| Voltage - Supply, Single (V+) | 1.5V~3.6V |
| Height | 880μm |
| Length | 3mm |
| Width | 3mm |
| RoHS Status | ROHS3 Compliant |
DG2617DN-T1-E4 Overview
Due to its 10-VFDFN Exposed Pad packaging, the electronic part is convenient for international shipping. This packaging method provides high reliability because it uses advanced packaging techniques. Multiplexers like this are mounted in the Surface Mount position. There is 2:1 ratio between the number of multiplexers and demultiplexers. Operating temperature extended to -40°C~85°C TA. Totally, there are 10 terminations. By its 1 channels, the electronic component provides high-quality output. A 3V voltage supply should turn on and run the electronic component. A total of 10 pins are injected into the electrical part body. A SPDT switching circuit is used to build these analog multiplexers. Look for analog switch ic variants by searching with DG2617. It has an internal resistance of 7Ohm. To find out what the functions of 10 pins are, please refer to their datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. Users should never supply a voltage higher than 3.6V to a switch device. An effective Single supply digital multiplexer. The lowest voltage the electronic part should receive is 1.5V. This multiplexer would work with 100nA current. This analogue multiplexer requires a voltage of 1.5V~3.6V when it drains from a single voltage supply. When the digital multiplexer is charged above 300μA, damage can occur. In order to operate the 2 inputs, there are several steps to follow. Multiplexer ics with 4 outputs are available.
DG2617DN-T1-E4 Features
1 Channels
Switch Circuit: SPDT
100nA Supply Current
DG2617DN-T1-E4 Applications
There are a lot of Vishay Siliconix DG2617DN-T1-E4 Analog Switches & Multiplexers ICs applications.
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Fault Tolerant Systems
- PDH Multiplexers
- Audio and video routing
- PCMCIA cards
- Multi-Line E1 Interface Cards
- Video switching
- Fiber In The Loop (FITL)
- Central office
- Automotive applications
