DG2618DN-T1-E4
| Parameters | |
|---|---|
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 10-VFDFN Exposed Pad |
| Number of Pins | 10 |
| Weight | 50.008559mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2016 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| Termination | SMD/SMT |
| Resistance | 7Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 1.191W |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.5mm |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG2618 |
| Pin Count | 10 |
| Number of Outputs | 4 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 3V |
| Polarity | Non-Inverting |
| Power Supplies | 3V |
| Number of Channels | 1 |
| Max Supply Voltage | 3.6V |
| Min Supply Voltage | 1.5V |
| Operating Supply Current | 100nA |
| Power Dissipation | 1.191W |
| Max Supply Current | 300μA |
| Turn On Delay Time | 69 ns |
| Number of Inputs | 2 |
| Supply Type | Single |
| Turn-Off Delay Time | 39 ns |
| On-State Resistance (Max) | 7Ohm |
| High Level Output Current | 150mA |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 32 dB |
| Current - Leakage (IS(off)) (Max) | 2nA |
| Channel Capacitance (CS(off), CD(off)) | 9pF |
| On-state Resistance Match-Nom | 0.1Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 69ns, 39ns |
| Charge Injection | 7pC |
| Channel-to-Channel Matching (ΔRon) | 100m Ω |
| Crosstalk | -80dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 76ns |
| Voltage - Supply, Single (V+) | 1.5V~3.6V |
| Height | 880μm |
| Length | 3mm |
| Width | 3mm |
| RoHS Status | ROHS3 Compliant |
DG2618DN-T1-E4 Overview
Shipping overseas is convenient with the electronic component packed in 10-VFDFN Exposed Pad. High reliability is achieved by using advanced packaging method Tape & Reel (TR). This analog switch is mounted in Surface Mount. 2:1 is the number of circuits in the multiplexer and demultiplexer. The operating temperature is extended to around -40°C~85°C TA. The total number of terminations is 10. A 1 channel electronic part produces high-quality output. Powered by a 3V voltage supply, the electrical part should be switched on and run. 10 pins are injected to the electronic part body. Unlike digital switches, these are based on SPDT switching circuits. Try searching for the analog switch ic with DG2618 if you are looking for variants. It has an internal resistance of 7Ohm. The datasheets for the 10 pins explain the functions. A analogue multiplexer of this type is a Multiplexer or Switches. In a normalsituation, users should not supply the switches with voltage higher than 3.6V. Digital switch that provides Single power at a cost-effective price. 1.5V is the lowest voltage that should be fed to the electronic electronic part. This multiplexer would work with 100nA current. A voltage of 1.5V~3.6V is required to drain this analog switch from a single voltage supply. A voltage higher than 300μA may cause damage to the switch multiplexer. This electrical part is compatible with 3V operating voltages. Among the inputs that can be operated are the 2 inputs. The analogue multiplexer has 4 outputs.
DG2618DN-T1-E4 Features
1 Channels
Switch Circuit: SPDT
100nA Supply Current
DG2618DN-T1-E4 Applications
There are a lot of Vishay Siliconix DG2618DN-T1-E4 Analog Switches & Multiplexers ICs applications.
- DVD-R
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- New designs requiring multiplexer functions
- Fiber In The Loop (FITL)
- Sample hold systems
- T1/E1 Terminals
- Video signal routing
- Industrial and process control systems
- RGB switches
- Channel Banks
