DG2706DN-T1-E4
| Parameters | |
|---|---|
| Number of Pins | 16 |
| Weight | 57.09594mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2016 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 5.5Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 525mW |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 3.15V |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | DG2706 |
| Pin Count | 16 |
| Number of Outputs | 8 |
| Qualification Status | Not Qualified |
| Power Supplies | 3.15V |
| Number of Channels | 1 |
| Max Supply Voltage | 4.3V |
| Min Supply Voltage | 1.65V |
| Operating Supply Current | 1μA |
| Power Dissipation | 525mW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 45 ns |
| Number of Inputs | 4 |
| Supply Type | Single |
| Turn-Off Delay Time | 35 ns |
| On-State Resistance (Max) | 5.5Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 70 dB |
| Current - Leakage (IS(off)) (Max) | 5nA |
| Channel Capacitance (CS(off), CD(off)) | 16pF |
| On-state Resistance Match-Nom | 0.3Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 45ns, 35ns |
| Charge Injection | 3pC |
| Channel-to-Channel Matching (ΔRon) | 300m Ω |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 55ns |
| Voltage - Supply, Single (V+) | 1.65V~4.3V |
| Height | 750μm |
| Length | 2.6mm |
| Width | 1.8mm |
| RoHS Status | ROHS3 Compliant |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-WFQFN |
DG2706DN-T1-E4 Overview
The electrical component comes in 16-WFQFN packaging, which makes it convenient to ship overseas. High reliability is provided by advanced packaging method Tape & Reel (TR). Mounted in Surface Mount is this multiplexer. Multiplexers and demultiplexers have a number of circuits 2:1. Extended operating temperature around -40°C~85°C TA. In total, there have been 16 terminations. A high-quality output is provided by the electrical component's 1 channels. Powered by a 3.15V voltage supply, the electrical part should be switched on and run. The electronic part body is injected with 16 pins. The analog switch ics are built using SPDT switching circuits. DG2706 can be used to search for analog multiplexer variants. As far as internal resistance is concerned, it has 5.5Ohm. Datasheets for functions of 16 pins are available. This switch device is a typical Multiplexer or Switches. Users should never supply a voltage higher than 4.3V to a switch device. Analog switch ics with Single supply type are cost-effective. The lowest voltage fed to the electronic component should be 1.65V. This multiplexer would work with 1μA current. A voltage of 1.65V~4.3V is required to drain this analog switch from a single voltage supply. It may damage the digital multiplexer if the voltage is higher than 1μA. Operating the 4 inputs requires 4 inputs. An output of 8 is provided by the digital multiplexer.
DG2706DN-T1-E4 Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
DG2706DN-T1-E4 Applications
There are a lot of Vishay Siliconix DG2706DN-T1-E4 Analog Switches & Multiplexers ICs applications.
- ATM
- Microprocessor Controlled Analog Systems
- USB 1.1 signal switching circuits
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Digital cross connects (DSX-1)
- Industrial control systems
- Transmit
- Audio and video signal routing
- Frame Relay Equipment
- Cable Telephony – NIU, Set-Top Box, Home Side Box
