DG2707DN-T1-E4
| Parameters | |
|---|---|
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-WFQFN |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2016 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 5.5Ohm |
| Max Power Dissipation | 525mW |
| Technology | CMOS |
| Terminal Position | QUAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3.15V |
| Terminal Pitch | 0.4mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG2707 |
| Pin Count | 16 |
| Operating Supply Voltage | 3V |
| Power Supplies | 3.15V |
| Number of Channels | 4 |
| Number of Circuits | 2 |
| Max Supply Voltage | 4.3V |
| Min Supply Voltage | 1.65V |
| Operating Supply Current | 1μA |
| Power Dissipation | 525mW |
| Logic Function | Multiplexer |
| Number of Inputs | 8 |
| Supply Type | Single |
| Supply Current-Max (Isup) | 0.001mA |
| -3db Bandwidth | 120MHz |
| On-State Resistance (Max) | 5.5Ohm |
| High Level Output Current | 300mA |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Off-state Isolation-Nom | 70 dB |
| Current - Leakage (IS(off)) (Max) | 5nA |
| Channel Capacitance (CS(off), CD(off)) | 16pF 42pF |
| On-state Resistance Match-Nom | 0.3Ohm |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 45ns, 35ns |
| Charge Injection | -14pC |
| Channel-to-Channel Matching (ΔRon) | 300m Ω |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 55ns |
| Switch-off Time-Max | 45ns |
| Voltage - Supply, Single (V+) | 1.65V~4.3V |
| Signal Current-Max | 0.3A |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
DG2707DN-T1-E4 Overview
Packed in 16-WFQFN, the electronic component is convenient for shipping overseas. This packaging method provides high reliability because it uses advanced packaging techniques. It is mounted in the position Surface Mount. In the multiplexer and demultiplexer, 4:1 represents the number of circuits. Operating temperature extended to -40°C~85°C TA. In total, there have been 16 terminations. By its 4 channels, the electronic component provides high-quality output. If the voltage supply is 3.15V volts, the electrical component should be turned on and run. An electrical component of this type can be found in the 16 series. Unlike digital switches, these are based on SP4T switching circuits. The multiplexer consists of 2 circuits. Try searching with DG2707 to find analog multiplexer variants. In this multiplexer, the internal resistance is 5.5Ohm. The functions of 16 pins can be found in the datasheets. normally, users should not supply switches with voltages higher than 4.3V. A cost-effective Single supply type analogue multiplexer. 1.65V should be the lowest voltage fed to the electronic component. The analogue multiplexer could operate on 1μA current. Analogue multiplexers require a 1.65V~4.3V voltage to drain from a single voltage supply. 3V operating voltages can be used with this electrical part. A 8 input needs to be operated.
DG2707DN-T1-E4 Features
4 Channels
Switch Circuit: SP4T
1μA Supply Current
-3db Bandwidth: 120MHz
DG2707DN-T1-E4 Applications
There are a lot of Vishay Siliconix DG2707DN-T1-E4 Analog Switches & Multiplexers ICs applications.
- Industrial
- PDH Multiplexers
- Remote Powered Equipment
- Cell phones
- Communication systems
- New designs requiring multiplexer functions
- Residential Gateways, Home Gateway/Router
- Data Acquisition Systems
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Avionics and Military Systems
