DG2714DL-T1-E3
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 6-TSSOP, SC-88, SOT-363 |
| Number of Pins | 6 |
| Weight | 28.009329mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| Resistance | 1.2Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 250mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 1.8V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG2714 |
| Pin Count | 6 |
| Number of Outputs | 2 |
| Number of Channels | 1 |
| Max Supply Voltage | 3.6V |
| Min Supply Voltage | 1.5V |
| Operating Supply Current | 10nA |
| Power Dissipation | 250mW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 51 ns |
| Number of Inputs | 1 |
| Supply Type | Single |
| Turn-Off Delay Time | 33 ns |
| On-State Resistance (Max) | 1.2Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 64 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 30pF |
| On-state Resistance Match-Nom | 0.06Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 51ns, 33ns |
| Charge Injection | 9pC |
| Channel-to-Channel Matching (ΔRon) | 60m Ω (Max) |
| Crosstalk | -64dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 75ns |
| Switch-off Time-Max | 39ns |
| Voltage - Supply, Single (V+) | 1.5V~3.6V |
| Height | 1mm |
| Length | 2mm |
| Width | 1.25mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
DG2714DL-T1-E3 Overview
The electronic part can be shipped overseas conveniently because it is packaged in 6-TSSOP, SC-88, SOT-363. To ensure high reliability, a new packaging method Tape & Reel (TR) is used. Multiplexers like this are mounted in the Surface Mount position. 2:1 is the ratio between multiplexers and demultiplexers. Extended operating temperature around -40°C~85°C TA. In total, 6 terminations have occurred. A high-quality output is provided by the electrical component's 1 channels. A 1.8V voltage supply should turn on and run the electronic component. 6 pins are injected to the electronic part body. The analog switch ics are built using SPDT switching circuits. Try searching for the analog switch ic with DG2714 if you are looking for variants. This digital multiplexer has 1.2Ohm internal resistance. To find out what the 6 pins do, please refer to the datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. Users should never supply a voltage higher than 3.6V to a switch device. A cost-effective Single supply type analogue multiplexer. There should be 1.5V voltage fed to the electrical part below 1.5V. For this multiplexer to operate, 10nA current would be sufficient. A voltage of 1.5V~3.6V is required for this switch device, which drains from a single voltage source. A voltage higher than 1μA may cause damage to the switch multiplexer. In order to operate the 1 inputs, there are several steps to follow. This digital multiplexer has 2 outputs.
DG2714DL-T1-E3 Features
1 Channels
Switch Circuit: SPDT
10nA Supply Current
DG2714DL-T1-E3 Applications
There are a lot of Vishay Siliconix DG2714DL-T1-E3 Analog Switches & Multiplexers ICs applications.
- SONET
- Video switching
- Switching Systems
- E1 Network Equipment
- Power routing
- PDAs
- Industrial
- SDH/SONET multiplexers
- Digital cross connects (DSX-1)
- Central office
