DG2716DL-T1-E3
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 5-TSSOP, SC-70-5, SOT-353 |
| Number of Pins | 5 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| Termination | SMD/SMT |
| Resistance | 600mOhm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 250mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 1.8V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG2716 |
| Pin Count | 5 |
| Number of Channels | 1 |
| Max Supply Voltage | 3.6V |
| Min Supply Voltage | 1.5V |
| Operating Supply Current | 10nA |
| Nominal Supply Current | 10nA |
| Power Dissipation | 250mW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 36 ns |
| Number of Inputs | 1 |
| Supply Type | Single |
| Turn-Off Delay Time | 33 ns |
| On-State Resistance (Max) | 600mOhm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 57 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 72pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 29ns, 26ns |
| Charge Injection | 9pC |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.5V~3.6V |
| Normal Position | NC |
| Length | 2mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
DG2716DL-T1-E3 Overview
As the electronic part is packed in 5-TSSOP, SC-70-5, SOT-353, international shipping is convenient. High reliability is achieved by using advanced packaging method Tape & Reel (TR). A switch device like this is mounted in Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Operation at a temperature around -40°C~85°C TA. There are 5 terminations totally. The electronic part provides high-quality output because it has 1 channels. Powered by a 1.8V voltage supply, the electrical part should be switched on and run. As part of the design of the 5 series, this electronic part has been incorporated into the system. Multiplexers built on a SPST - NC switching circuit are built. If you are looking for variants of the digital switch, trying search with DG2716. The internal resistance of this digital multiplexer is 600mOhm. You can find the functions of the 5 pins in the datasheets. Multiplexer or Switches is a typical switch device. normally, users should not supply switches with voltages higher than 3.6V. Digital switch that provides Single power at a cost-effective price. There should be 1.5V voltage fed to the electrical part below 1.5V. The analogue multiplexer could operate on 10nA current. A voltage of 1.5V~3.6V is required for this switch device, which drains from a single voltage source. A digital multiplexer may suffer damage if voltage is applied above 1μA. There are 1 inputs to be operated.
DG2716DL-T1-E3 Features
1 Channels
Switch Circuit: SPST - NC
10nA Supply Current
DG2716DL-T1-E3 Applications
There are a lot of Vishay Siliconix DG2716DL-T1-E3 Analog Switches & Multiplexers ICs applications.
- Multiplexers
- HDTV
- Audio and video routing
- Microprocessor controlled systems
- Channel Banks
- E1 Network Equipment
- Video switching
- PBXs
- Mechanical reed relay replacement
- Audio and video switching
