DG2717DX-T1-E3
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SOT-563, SOT-666 |
| Number of Pins | 6 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| Resistance | 700mOhm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 172mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | FLAT |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.5mm |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG2717 |
| Pin Count | 6 |
| Number of Outputs | 2 |
| Qualification Status | Not Qualified |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 4.3V |
| Min Supply Voltage | 1.6V |
| Operating Supply Current | 10nA |
| Nominal Supply Current | 10nA |
| Power Dissipation | 172mW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 74 ns |
| Number of Inputs | 1 |
| Supply Type | Single |
| Turn-Off Delay Time | 34 ns |
| On-State Resistance (Max) | 700mOhm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 54 dB |
| Channel Capacitance (CS(off), CD(off)) | 76pF |
| On-state Resistance Match-Nom | 0.06Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 44ns, 29ns |
| Charge Injection | 28pC |
| Channel-to-Channel Matching (ΔRon) | 600m Ω (Max) |
| Crosstalk | -57dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 44ns |
| Voltage - Supply, Single (V+) | 1.6V~4.3V |
| Normal Position | NC |
| RoHS Status | ROHS3 Compliant |
DG2717DX-T1-E3 Overview
The electronic part can be shipped overseas conveniently because it is packaged in SOT-563, SOT-666. The advanced packaging method Tape & Reel (TR) provides high reliability. Surface Mount is where this multiplexer is located. In the multiplexer and demultiplexer, 2:1 represents the number of circuits. Around -40°C~85°C TA is the extended operating temperature. Total terminations are 6. As a result of its 1 channels, this electronic component provides high-quality output. With a 3V voltage supply, the electrical component should be turned on and run. Into the electrical component body are injected 6 pins. SPDT switching circuits are used in these analog switch ics. The multiplexer consists of 1 circuits. DG2717 can be used to search for analog multiplexer variants. In this multiplexer, the internal resistance is 700mOhm. To find out what the functions of 6 pins are, please refer to their datasheets. Theswitch device is a typical Multiplexer or Switches. normally, users should not supply switches with voltages higher than 4.3V. A cost-effective Single supply type analogue multiplexer. In order for the electronic part to function properly, the lowest voltage should be 1.6V. 10nA current would be enough for this multiplexer to operate. A voltage of 1.6V~4.3V is required to drain this analog switch from a single voltage supply. Putting voltage greater than 1μA on the multiplexer may cause damage. There are 1 inputs to be operated. The analog switch ics includes 2 outputs.
DG2717DX-T1-E3 Features
1 Channels
Switch Circuit: SPDT
10nA Supply Current
DG2717DX-T1-E3 Applications
There are a lot of Vishay Siliconix DG2717DX-T1-E3 Analog Switches & Multiplexers ICs applications.
- Multiplexers
- Relay replacements
- Isolation
- Communications systems
- ATM
- Microwave transmission systems
- Avionics
- Channelized and Unchannelized DS3 applications
- Precision instrumentation
- Communication systems
