DG2718DN-T1-E4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-VFQFN Exposed Pad |
| Number of Pins | 16 |
| Weight | 57.09594mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2009 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 600mOhm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 1.385W |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 1.8V |
| Terminal Pitch | 0.5mm |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG2718 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Power Supplies | 1.8/3V |
| Number of Channels | 2 |
| Number of Circuits | 2 |
| Max Supply Voltage | 3.6V |
| Min Supply Voltage | 1.65V |
| Operating Supply Current | 1μA |
| Max Supply Current | 1μA |
| Turn On Delay Time | 57 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 45 ns |
| On-State Resistance (Max) | 600mOhm |
| Multiplexer/Demultiplexer Circuit | 2:2 |
| Off-state Isolation-Nom | 74 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 102pF |
| Switch Circuit | DPDT |
| Switch Time (Ton, Toff) (Max) | 57ns, 45ns |
| Charge Injection | 232pC |
| Channel-to-Channel Matching (ΔRon) | 50m Ω |
| Crosstalk | -75dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 94ns |
| Switch-off Time-Max | 55ns |
| Voltage - Supply, Single (V+) | 1.65V~3.6V |
| Height | 900μm |
| Length | 3mm |
| Width | 3mm |
| RoHS Status | ROHS3 Compliant |
DG2718DN-T1-E4 Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-VFQFN Exposed Pad. High reliability is achieved by using advanced packaging method Tape & Reel (TR). In Surface Mount, this analog switch is mounted. 2:2 is the number of circuits in the multiplexer and demultiplexer. Operational temperature extended around -40°C~85°C TA. A total of 16 terminations have been recorded. This electronic part offers high-quality output due to its 2 channels. Turning on and running the electrical part should be easy with a 1.8V voltage supply. A key feature of the 16 series is the inclusion of this electronic part as part of its design. Unlike digital switches, these are based on DPDT switching circuits. The multiplexer consists of 2 circuits. Look for analog switch ic variants by searching with DG2718. The internal resistance of this digital multiplexer is 600mOhm. To find out what the 16 pins do, please refer to the datasheets. This switch device is a typical Multiplexer or Switches. Users should never supply a voltage higher than 3.6V to a switch device. Analogue multiplexer with a Single supply type that is cost-effective. The lowest voltage fed to the electronic component should be 1.65V. An operating current of 1μA would be sufficient for this switch device. This analog switch requires a voltage of 1.65V~3.6V to drain from a single voltage supply. If put voltage greater than 1μA on the device, damage may be caused to the analogue multiplexer. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them.
DG2718DN-T1-E4 Features
2 Channels
Switch Circuit: DPDT
1μA Supply Current
DG2718DN-T1-E4 Applications
There are a lot of Vishay Siliconix DG2718DN-T1-E4 Analog Switches & Multiplexers ICs applications.
- Cable Modem
- HDTV
- New designs requiring multiplexer functions
- Communications systems
- Frame Relay Equipment
- Multiplexers
- Remote wireless modules
- Battery-powered systems
- Data Acquisition Systems
- RGB switches
