DG271BCJ-E3
| Parameters | |
|---|---|
| Turn-Off Delay Time | 65 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 50Ohm |
| Min Dual Supply Voltage | 7V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 85 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 65ns, 65ns |
| Charge Injection | -5pC |
| Crosstalk | -100dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NC |
| Voltage - Supply, Dual (V±) | ±15V |
| Height | 3.81mm |
| Length | 21.33mm |
| Width | 7.11mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Weight | 1.627801g |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2009 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Termination | Through Hole |
| Resistance | 50Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 470mW |
| Technology | CMOS |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Base Part Number | DG271 |
| Pin Count | 16 |
| Operating Supply Voltage | 15V |
| Number of Channels | 1 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 13V |
| Operating Supply Current | 5.5mA |
| Nominal Supply Current | 5.5mA |
| Power Dissipation | 470mW |
| Max Supply Current | 7.5mA |
| Throw Configuration | SPST |
| Turn On Delay Time | 65 ns |
| Number of Inputs | 4 |
| Supply Type | Dual |
| Neg Supply Voltage-Nom (Vsup) | -15V |
DG271BCJ-E3 Overview
The electrical component comes in 16-DIP (0.300, 7.62mm) packaging, which makes it convenient to ship overseas. High reliability is ensured by the advanced packaging method Tube. The multiplexer is located in Through Hole. Multiplexers and demultiplexers have a number of circuits 1:1. The operating temperature is extended to around -40°C~85°C TA. A total of 16 terminations have been recorded. Due to its 1 channels, the electrical component produces high-quality output. An 15V voltage supply should allow the electrical part to be turned on and run. It is injected into the electrical part body with 16 pins. A SPST - NC switching circuit is used for these analog switches. Try searching for the analog switch ic with DG271 if you are looking for variants. Analog switches have 50Ohm internal resistance. For functions related to 16 pins, please refer to the datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. It is generally not recommended to supply a voltage higher than 36V to the switch device in normal circumstances. A analog switch ic that has a cost-effective Dual supply type. The lowest voltage fed to the electronic component should be 13V. For this multiplexer to operate, 5.5mA current would be sufficient. Putting voltage greater than 7.5mA on the multiplexer may cause damage. For this multiplexer, dual supply voltage is feasible, but it should not exceed 22V. The voltage should be at least 7V if you are using dual power supplies. This electrical part is compatible with 15V operating voltages. In order to operate the 4 inputs, there are several steps to follow.
DG271BCJ-E3 Features
1 Channels
Switch Circuit: SPST - NC
5.5mA Supply Current
DG271BCJ-E3 Applications
There are a lot of Vishay Siliconix DG271BCJ-E3 Analog Switches & Multiplexers ICs applications.
- Ultrasound
- Modems
- Avionics
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- HDTV
- Automatic test equipment
- New designs requiring multiplexer functions
- Relay replacements
- Video switching
- Industrial
