Parameters |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-SOIC (0.154, 3.90mm Width) |
Number of Pins |
16 |
Weight |
665.986997mg |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
Resistance |
50Ohm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
600mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
15V |
Terminal Pitch |
1.27mm |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
DG271 |
Pin Count |
16 |
Operating Supply Voltage |
15V |
Number of Channels |
1 |
Max Supply Voltage |
36V |
Min Supply Voltage |
13V |
Operating Supply Current |
5.5mA |
Nominal Supply Current |
5.5mA |
Power Dissipation |
600mW |
Max Supply Current |
7.5mA |
Throw Configuration |
SPST |
Turn On Delay Time |
65 ns |
Number of Inputs |
4 |
Supply Type |
Dual |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
65 ns |
Max Dual Supply Voltage |
22V |
On-State Resistance (Max) |
50Ohm |
Min Dual Supply Voltage |
7V |
Dual Supply Voltage |
15V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
85 dB |
Current - Leakage (IS(off)) (Max) |
1nA |
Channel Capacitance (CS(off), CD(off)) |
8pF 8pF |
Switch Circuit |
SPST - NC |
Switch Time (Ton, Toff) (Max) |
65ns, 65ns |
Charge Injection |
-5pC |
Crosstalk |
-100dB @ 100kHz |
Switching |
BREAK-BEFORE-MAKE |
Normal Position |
NC |
Voltage - Supply, Dual (V±) |
±15V |
Height |
1.55mm |
Length |
10mm |
Width |
4mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
DG271BDY-E3 Overview
The electronic component is convenient to ship overseas because it is packed in a 16-SOIC (0.154, 3.90mm Width). In order to provide high reliability, an advanced packaging method Tube is used. Surface Mount is where this multiplexer is located. Multiplexers and demultiplexers have a ratio of 1:1. Extended operating temperature around -40°C~85°C TA. In total, there have been 16 terminations. The electronic part delivers high-quality output through its 1 channels. If the voltage supply is 15V volts, the electrical component should be turned on and run. A total of 16 pins are injected into the body of the electronic part. Circuits based on SPST - NC switching are used to construct these analog switch ics. Try searching with DG271 to find analog multiplexer variants. Internally, this switch multiplexer has a resistance of 50Ohm. For details about the functions of 16 pins, please refer to the datasheets. In this analog multiplexer, the value is Multiplexer or Switches. In a normalsituation, users should not supply the switches with voltage higher than 36V. The analog switch ic is of the Dual supply type and is cost-effective. A low voltage of 13V should be applied to the electronic component. The switch device would be able to operate with 5.5mA current. The analogue multiplexer may be damaged if voltage is greater than 7.5mA. Despite this switch device's dual supply capability, its voltage should not exceed 22V. The voltage should be at least 7V if you are using dual power supplies. Operating voltages of 15V are compatible with the electrical part. In order to operate the 4 inputs, there are several steps to follow.
DG271BDY-E3 Features
1 Channels
Switch Circuit: SPST - NC
5.5mA Supply Current
DG271BDY-E3 Applications
There are a lot of Vishay Siliconix DG271BDY-E3 Analog Switches & Multiplexers ICs applications.
- SONET
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Remote Powered Equipment
- Mechanical reed relay replacement
- ATM
- Microprocessor controlled systems
- Industrial control systems
- Medical Instrumentation
- Medical
- Avionics and Military Systems