DG271BDY-T1-E3

65ns, 65ns SPST - NC 50Ohm Analog Switches BREAK-BEFORE-MAKE DG271 16 Pins 1nA 15V 16-SOIC (0.154, 3.90mm Width)

Manufacturer: Vishay Siliconix
Nocochips NO: 880-DG271BDY-T1-E3
Package: 16-SOIC (0.154, 3.90mm Width)
Datasheet: PDF
Stock: 585
Description: 65ns, 65ns SPST - NC 50Ohm Analog Switches BREAK-BEFORE-MAKE DG271 16 Pins 1nA 15V 16-SOIC (0.154, 3.90mm Width)(Kg)

Details

Tags

Parameters
Factory Lead Time	1 Week
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	16-SOIC (0.154, 3.90mm Width)
Number of Pins	16
Weight	665.986997mg
Operating Temperature	-40°C~85°C TA
Packaging	Tape & Reel (TR)
Published	2009
JESD-609 Code	e3
Pbfree Code	yes
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	16
Resistance	50Ohm
Terminal Finish	Matte Tin (Sn)
Subcategory	Multiplexer or Switches
Max Power Dissipation	600mW
Technology	CMOS
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	4
Supply Voltage	15V
Terminal Pitch	1.27mm
Time@Peak Reflow Temperature-Max (s)	30
Base Part Number	DG271
Pin Count	16
Qualification Status	Not Qualified
Operating Supply Voltage	15V
Number of Channels	1
Max Supply Voltage	36V
Min Supply Voltage	13V
Operating Supply Current	5.5mA
Power Dissipation	600mW
Max Supply Current	7.5mA
Throw Configuration	SPST
Turn On Delay Time	65 ns
Number of Inputs	4
Supply Type	Dual
Neg Supply Voltage-Nom (Vsup)	-15V
Turn-Off Delay Time	65 ns
Max Dual Supply Voltage	22V
On-State Resistance (Max)	50Ohm
Min Dual Supply Voltage	7V
Dual Supply Voltage	15V
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	85 dB
Current - Leakage (IS(off)) (Max)	1nA
Channel Capacitance (CS(off), CD(off))	8pF 8pF
Switch Circuit	SPST - NC
Switch Time (Ton, Toff) (Max)	65ns, 65ns
Charge Injection	-5pC
Crosstalk	-100dB @ 100kHz
Switching	BREAK-BEFORE-MAKE
Drain to Source Resistance	50Ohm
Normal Position	NC
Voltage - Supply, Dual (V±)	±15V
Height	1.55mm
Length	10mm
Width	4mm
REACH SVHC	Unknown
RoHS Status	ROHS3 Compliant

DG271BDY-T1-E3 Overview

Presented in 16-SOIC (0.154, 3.90mm Width), this electrical component is convenient for overseas shipping. Advanced packaging method Tape & Reel (TR) is used to provide high reliability. Surface Mount is where this multiplexer is located. Multiplexers and demultiplexers have the same number of circuits 1:1. Operational temperature extended around -40°C~85°C TA. In total, there have been 16 terminations. High-quality output is provided by the electronic component's 1 channels. When the electronic component is given a voltage of 15V, it should be turned on and run. As part of its design, the 16 series is equipped with this electronic component. These analog multiplexers are built based on SPST - NC switching circuits. Using the DG271 search parameter, you can discover variants of the switch. As far as internal resistance is concerned, it has 50Ohm. Please refer to the datasheets for 16 pins functions. It is a typical Multiplexer or Switches analog multiplexer. In normalcircumstances, users should not exceed 36V volts for the multiplexer. Analog switch ics with Dual supply type are cost-effective. 13V is the lowest voltage that should be fed to the electronic electronic part. The switch device would be able to operate with 5.5mA current. A voltage higher than 7.5mA may cause damage to the switch multiplexer. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 22V. For dual power supplies, a voltage of at least 7V should be attached. There is a voltage range of 15V operating voltages for the electrical part. Operating 4 inputs is required. Drain to Source resistance for this electronic component is 50Ohm.