DG2720DN-T1-E4
| Parameters | |
|---|---|
| Height | 550μm |
| Length | 1.8mm |
| Width | 1.4mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 10-UFQFN |
| Number of Pins | 10 |
| Weight | 7.002332mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2016 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| Resistance | 7Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 208mW |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG2720 |
| Pin Count | 10 |
| Number of Outputs | 4 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 3V |
| Power Supplies | 3V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 4.3V |
| Min Supply Voltage | 2.6V |
| Operating Supply Current | 2μA |
| Nominal Supply Current | 2μA |
| Power Dissipation | 208mW |
| Turn On Delay Time | 30 ns |
| Data Rate | 480 Mbps |
| Supply Type | Single |
| Bandwidth | 620MHz |
| Turn-Off Delay Time | 25 ns |
| On-State Resistance (Max) | 7Ohm |
| Multiplexer/Demultiplexer Circuit | 2:2 |
| Off-state Isolation-Nom | 30 dB |
| Current - Leakage (IS(off)) (Max) | 100nA |
| Channel Capacitance (CS(off), CD(off)) | 4pF |
| On-state Resistance Match-Nom | 0.35Ohm |
| Switch Circuit | DPDT |
| Switch Time (Ton, Toff) (Max) | 30ns, 25ns |
| Charge Injection | 0.5pC |
| Channel-to-Channel Matching (ΔRon) | 350m Ω |
| Crosstalk | -49dB @ 240MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2.6V~4.3V |
DG2720DN-T1-E4 Overview
Shipping overseas is convenient due to the electrical component's packing in 10-UFQFN. The advanced packaging method Tape & Reel (TR) provides high reliability. In Surface Mount, this analog switch is mounted. The ratio between the number of multiplexer and demultiplexer circuits is 2:2. Temperatures around -40°C~85°C TA are extended for operation. Total terminations are 10. As a result of its 1 channels, this electronic component provides high-quality output. When the electronic component is given a voltage of 3V, it should be turned on and run. As part of the design of the 10 series, this electronic part has been incorporated into the system. DPDT switching circuits are used in these analog switch ics. The circuits in this analogue multiplexer number 2. Use DG2720 to search for variants of the digital switches. A 7Ohm internal resistance characterizes this multiplexer. To find out what the functions of 10 pins are, please refer to their datasheets. Theswitch device is a typical Multiplexer or Switches. Multiplexers should not be powered above 4.3V in normal situations. Analogue multiplexer with a Single supply type that is cost-effective. The lowest voltage fed to the electronic component should be 2.6V. For this digital switch to work, 2μA current would suffice. Using a single voltage supply, this switch device consumes 2.6V~4.3V volts. A voltage of 3V can be used to operate the electronic component. The transfer of data can be performed over 620MHz bandwidths. The analog switch ics includes 4 outputs.
DG2720DN-T1-E4 Features
1 Channels
Switch Circuit: DPDT
2μA Supply Current
Bandwidth: 620MHz
DG2720DN-T1-E4 Applications
There are a lot of Vishay Siliconix DG2720DN-T1-E4 Analog Switches & Multiplexers ICs applications.
- Audio and video switching
- T1/E1 Terminals
- High speed data transmission line cards
- Audio and video routing
- Switching Systems
- Remote wireless modules
- Fault Tolerant Systems
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Medical systems
- Optical Applications
