DG2721DN-T1-E4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 10-UFQFN |
| Number of Pins | 10 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| Resistance | 7Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG2721 |
| Pin Count | 10 |
| Number of Outputs | 4 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 3V |
| Power Supplies | 3V |
| Number of Channels | 2 |
| Number of Circuits | 1 |
| Max Supply Voltage | 4.3V |
| Min Supply Voltage | 2.6V |
| Operating Supply Current | 2μA |
| Power Dissipation | 208mW |
| Throw Configuration | SPDT |
| Supply Type | Single |
| -3db Bandwidth | 620MHz |
| On-State Resistance (Max) | 7Ohm |
| Multiplexer/Demultiplexer Circuit | 2:2 |
| Off-state Isolation-Nom | 30 dB |
| Current - Leakage (IS(off)) (Max) | 100nA |
| Channel Capacitance (CS(off), CD(off)) | 4pF |
| On-state Resistance Match-Nom | 0.35Ohm |
| Switch Circuit | DTDT |
| Switch Time (Ton, Toff) (Max) | 30ns, 25ns |
| Charge Injection | 0.5pC |
| Channel-to-Channel Matching (ΔRon) | 350m Ω |
| Crosstalk | -49dB @ 240MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 30ns |
| Height Seated (Max) | 0.6mm |
| RoHS Status | ROHS3 Compliant |
DG2721DN-T1-E4 Overview
The electronic part can be shipped overseas conveniently because it is packaged in 10-UFQFN. High reliability is achieved by using advanced packaging method Tape & Reel (TR). A switch device like this is mounted in Surface Mount. 2:2 is the ratio of multiplexer to demultiplexer circuits. The operating temperature is extended to around -40°C~85°C TA. In total, there have been 10 terminations. High-quality output is provided by the electronic component's 2 channels. When a voltage supply of 3V is used, the electronic component should be turned on and run. A total of 10 pins are injected into the electrical part body. A DTDT switching circuit is used for these analog switches. 1 circuits are used in this analogue multiplexer. Try searching with DG2721 to find analog multiplexer variants. The internal resistance of this digital multiplexer is 7Ohm. Datasheets for 10 pin functions are available upon request. In this analog multiplexer, the value is Multiplexer or Switches. Users shouldn't supply more than 4.3V voltage to the switch device. Analogue multiplexers of the Single supply type that are cost-effective. A low voltage of 2.6V should be applied to the electronic component. This multiplexer would work with 2μA current. There is a voltage range of 3V operating voltages for the electrical part. There are 4 outputs on the analogue multiplexer.
DG2721DN-T1-E4 Features
2 Channels
Switch Circuit: DTDT
2μA Supply Current
-3db Bandwidth: 620MHz
DG2721DN-T1-E4 Applications
There are a lot of Vishay Siliconix DG2721DN-T1-E4 Analog Switches & Multiplexers ICs applications.
- Data switching
- PBXs
- Optical Applications
- Isolation
- Industrial
- Switching Systems
- Remote wireless modules
- Microwave transmission systems
- Cell phones
- Sample-and-hold systems
