DG2722DN-T1-E4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 10-UFQFN |
| Number of Pins | 10 |
| Weight | 7.002332mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2016 |
| JESD-609 Code | e4 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| Resistance | 8Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 208mW |
| Technology | CMOS |
| Terminal Position | QUAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | DG2722 |
| Pin Count | 10 |
| Number of Outputs | 4 |
| Operating Supply Voltage | 3V |
| Power Supplies | 3V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 4.3V |
| Min Supply Voltage | 2.6V |
| Operating Supply Current | 2μA |
| Power Dissipation | 208mW |
| Turn On Delay Time | 30 ns |
| Data Rate | 480 Mbps |
| Supply Type | Single |
| Bandwidth | 900MHz |
| Turn-Off Delay Time | 25 ns |
| On-State Resistance (Max) | 8Ohm |
| Multiplexer/Demultiplexer Circuit | 2:2 |
| Off-state Isolation-Nom | 30 dB |
| Current - Leakage (IS(off)) (Max) | 100nA |
| Channel Capacitance (CS(off), CD(off)) | 2.2pF |
| On-state Resistance Match-Nom | 0.8Ohm |
| Switch Circuit | DPDT |
| Switch Time (Ton, Toff) (Max) | 30ns, 25ns |
| Charge Injection | 0.5pC |
| Channel-to-Channel Matching (ΔRon) | 800m Ω |
| Crosstalk | -45dB @ 240MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2.6V~4.3V |
| Height | 550μm |
| Length | 1.8mm |
| Width | 1.4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
DG2722DN-T1-E4 Overview
Shipping overseas is convenient due to the electrical component's packing in 10-UFQFN. The advanced packaging method Tape & Reel (TR) provides high reliability. Mounted in Surface Mount is this multiplexer. In the multiplexer and demultiplexer, 2:2 represents the number of circuits. Operating temperature around -40°C~85°C TA extended. In total, there have been 10 terminations. The electronic part delivers high-quality output through its 1 channels. Powered by a 3V voltage supply, the electrical part should be switched on and run. It is part of the design of the 10 series that this electronic component is included. On the other hand, analog switches can be constructed using DPDT switching circuits. This multiplexer is composed of 2 circuits. Using the DG2722 search parameter, you can discover variants of the switch. In this multiplexer, the internal resistance is 8Ohm. To find out what the 10 pins do, please refer to the datasheets. A analogue multiplexer of this type is a Multiplexer or Switches. Users should never supply a voltage higher than 4.3V to a switch device. Analogue multiplexers of the Single supply type that are cost-effective. It is recommended to use 2.6V as the lowest voltage for the electrical part. In order to operate this switch device, it would need a current of 2μA. This analog switch requires a voltage of 2.6V~4.3V to drain from a single voltage supply. This electrical part is compatible with 3V operating voltages. It is possible to transfer data over a 900MHz-bandwidth. The analog switch ics includes 4 outputs.
DG2722DN-T1-E4 Features
1 Channels
Switch Circuit: DPDT
2μA Supply Current
Bandwidth: 900MHz
DG2722DN-T1-E4 Applications
There are a lot of Vishay Siliconix DG2722DN-T1-E4 Analog Switches & Multiplexers ICs applications.
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Battery Powered Instruments
- DVD-R
- PBX interfaces
- Multi-Line E1 Interface Cards
- Microwave transmission systems
- Microprocessor Controlled Analog Systems
- PDH Multiplexers
- Multiplexers
- Avionics and Military Systems
