banner_page

DG2727DN-T1-E4

QUAD Analog Switches BREAK-BEFORE-MAKE DG2727 8 Pins 3V 8-UFQFN


  • Manufacturer: Vishay Siliconix
  • Nocochips NO: 880-DG2727DN-T1-E4
  • Package: 8-UFQFN
  • Datasheet: PDF
  • Stock: 279
  • Description: QUAD Analog Switches BREAK-BEFORE-MAKE DG2727 8 Pins 3V 8-UFQFN(Kg)

Details

Tags

Parameters
Mount Surface Mount
Mounting Type Surface Mount
Package / Case 8-UFQFN
Number of Pins 8
Packaging Cut Tape (CT)
Published 2015
JESD-609 Code e4
Pbfree Code yes
Part Status Obsolete
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 8
Resistance 1Ohm
Terminal Finish Nickel/Palladium/Gold (Ni/Pd/Au)
Max Operating Temperature 85°C
Min Operating Temperature -40°C
Subcategory Multiplexer or Switches
Max Power Dissipation 190mW
Technology CMOS
Terminal Position QUAD
Terminal Form NO LEAD
Peak Reflow Temperature (Cel) 260
Number of Functions 2
Supply Voltage 3V
Terminal Pitch 0.4mm
Reach Compliance Code unknown
Time@Peak Reflow Temperature-Max (s) 30
Base Part Number DG2727
Pin Count 8
Number of Outputs 2
Qualification Status Not Qualified
Temperature Grade INDUSTRIAL
Number of Channels 1
Max Supply Voltage 4.3V
Min Supply Voltage 1.6V
Operating Supply Current 1μA
Power Dissipation 190mW
Max Supply Current 1μA
Throw Configuration SPST
Turn On Delay Time 67 ns
Supply Type Single
Turn-Off Delay Time 40 ns
Off-state Isolation-Nom 58 dB
On-state Resistance Match-Nom 0.1Ohm
Switching BREAK-BEFORE-MAKE
Normal Position NO
Height Seated (Max) 0.6mm
Length 1.4mm
Width 1.4mm
RoHS Status ROHS3 Compliant

DG2727DN-T1-E4 Overview


The electronic part can be shipped overseas conveniently because it is packaged in 8-UFQFN. To ensure high reliability, a new packaging method Cut Tape (CT) is used. It is mounted in the position Surface Mount. Totally, there are 8 terminations. Due to its 1 channels, the electrical component produces high-quality output. Powered by a 3V voltage supply, the electrical part should be switched on and run. This electronic part can be found in the 8 series. If you are looking for variants of the digital switch, trying search with DG2727. This digital multiplexer has 1Ohm internal resistance. Datasheets for functions of 8 pins are available. There is a standard Multiplexer or Switches analogue multiplexer here. A voltage higher than 4.3V should not normally be supplied to the switches. A analog switch ic that has a cost-effective Single supply type. The lowest voltage the electronic part should receive is 1.6V. 1μA current would be enough for this multiplexer to operate. A voltage higher than 1μA may cause damage to the switch multiplexer. A temperature above 85°C is not suitable for operation of the analogue multiplexer. This digital multiplexer has 2 outputs.

DG2727DN-T1-E4 Features


1 Channels
1μA Supply Current

DG2727DN-T1-E4 Applications


There are a lot of Vishay Siliconix DG2727DN-T1-E4 Analog Switches & Multiplexers ICs applications.

  • Data switching
  • SDH
  • Sample hold systems
  • Existing multiplexer applications (both fault-protected and nonfault-protected)
  • Medical
  • PBX interfaces
  • Relay Replacement
  • Optical Applications
  • SONET/SDH ADM
  • E1 Network Equipment

Write a review

Note: HTML is not translated!
    Bad           Good