DG2730DN-T1-GE4
| Parameters | |
|---|---|
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2016 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| Resistance | 8Ohm |
| Terminal Finish | NICKEL PALLADIUM GOLD |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 208mW |
| Technology | CMOS |
| Terminal Position | QUAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG2730 |
| Pin Count | 10 |
| Number of Outputs | 4 |
| Operating Supply Voltage | 3V |
| Power Supplies | 3V |
| Number of Channels | 2 |
| Number of Circuits | 1 |
| Max Supply Voltage | 4.3V |
| Min Supply Voltage | 2.6V |
| Operating Supply Current | 2μA |
| Nominal Supply Current | 2μA |
| Power Dissipation | 208mW |
| Turn On Delay Time | 30 ns |
| Data Rate | 480 Mbps |
| Number of Inputs | 2 |
| Supply Type | Single |
| Turn-Off Delay Time | 25 ns |
| -3db Bandwidth | 900MHz |
| On-State Resistance (Max) | 8Ohm |
| Multiplexer/Demultiplexer Circuit | 2:2 |
| Off-state Isolation-Nom | 30 dB |
| Current - Leakage (IS(off)) (Max) | 100nA |
| Channel Capacitance (CS(off), CD(off)) | 2.2pF |
| On-state Resistance Match-Nom | 0.8Ohm |
| Switch Circuit | DPDT |
| Switch Time (Ton, Toff) (Max) | 30ns, 25ns |
| Charge Injection | 0.5pC |
| Channel-to-Channel Matching (ΔRon) | 800m Ω |
| Crosstalk | -45dB @ 240MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2.6V~4.3V |
| Height Seated (Max) | 0.6mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 10-UFQFN |
| Number of Pins | 10 |
DG2730DN-T1-GE4 Overview
This electronic part is conveniently packaged in 10-UFQFN, making it easy to ship abroad. High reliability is achieved by using advanced packaging method Tape & Reel (TR). The multiplexer is located in Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 2:2. An extended operating temperature of -40°C~85°C TA degrees Celsius. 10 terminations have been made so far. By its 2 channels, the electronic component provides high-quality output. When the electronic component is given a voltage of 3V, it should be turned on and run. This electronic part can be found in the 10 series. Circuits based on DPDT switching are used to construct these analog switch ics. A total of 1 circuits make up this switch device. Try searching with DG2730 if you're looking for variants. Analog switches have 8Ohm internal resistance. To find out what the 10 pins do, please refer to the datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 4.3V to the switch device in normal circumstances. Analogue multiplexers of the Single supply type that are cost-effective. The lowest voltage fed to the electronic component should be 2.6V. The analogue multiplexer could operate on 2μA current. An analogue multiplexer drains from a single voltage supply at 2.6V~4.3V. The electronic component can function from 3V. The electrical component supports 2 inputs. The analog switch ics includes 4 outputs.
DG2730DN-T1-GE4 Features
2 Channels
Switch Circuit: DPDT
2μA Supply Current
-3db Bandwidth: 900MHz
DG2730DN-T1-GE4 Applications
There are a lot of Vishay Siliconix DG2730DN-T1-GE4 Analog Switches & Multiplexers ICs applications.
- Communication systems
- 65 V DACs
- Transmit
- Digital access cross connects
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Mechanical reed relay replacement
- Precision instrumentation
- Switching Systems
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Residential Gateways, Home Gateway/Router
