banner_page

DG2731DN-T1-E4

110ns, 30ns SPDT 450mOhm DUAL Analog Switches BREAK-BEFORE-MAKE DG2731 10 Pins 1nA 3V 10-VFDFN Exposed Pad


  • Manufacturer: Vishay Siliconix
  • Nocochips NO: 880-DG2731DN-T1-E4
  • Package: 10-VFDFN Exposed Pad
  • Datasheet: PDF
  • Stock: 247
  • Description: 110ns, 30ns SPDT 450mOhm DUAL Analog Switches BREAK-BEFORE-MAKE DG2731 10 Pins 1nA 3V 10-VFDFN Exposed Pad(Kg)

Details

Tags

Parameters
Mount Surface Mount
Mounting Type Surface Mount
Package / Case 10-VFDFN Exposed Pad
Number of Pins 10
Weight 50.008559mg
Operating Temperature -40°C~85°C TA
Packaging Tape & Reel (TR)
Published 2009
JESD-609 Code e4
Pbfree Code yes
Part Status Obsolete
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 10
Resistance 400mOhm
Terminal Finish Nickel/Palladium/Gold (Ni/Pd/Au)
Subcategory Multiplexer or Switches
Max Power Dissipation 1.191W
Technology CMOS
Terminal Position DUAL
Terminal Form NO LEAD
Peak Reflow Temperature (Cel) 260
Number of Functions 2
Supply Voltage 3V
Terminal Pitch 0.5mm
Reach Compliance Code unknown
Time@Peak Reflow Temperature-Max (s) 40
Base Part Number DG2731
Output SEPARATE OUTPUT
Pin Count 10
Qualification Status Not Qualified
Number of Channels 1
Number of Circuits 2
Max Supply Voltage 4.3V
Min Supply Voltage 1.65V
Operating Supply Current 1μA
Max Supply Current 1μA
Turn On Delay Time 110 ns
Supply Type Single
Turn-Off Delay Time 30 ns
On-State Resistance (Max) 450mOhm
Multiplexer/Demultiplexer Circuit 2:1
Off-state Isolation-Nom 75 dB
Current - Leakage (IS(off)) (Max) 1nA
Channel Capacitance (CS(off), CD(off)) 104pF
On-state Resistance Match-Nom 0.03Ohm
Switch Circuit SPDT
Switch Time (Ton, Toff) (Max) 110ns, 30ns
Charge Injection 9pC
Channel-to-Channel Matching (ΔRon) 30m Ω
Crosstalk -75dB @ 100kHz
Switching BREAK-BEFORE-MAKE
Voltage - Supply, Single (V+) 1.65V~4.3V
Height 880μm
Length 3mm
Width 3mm
RoHS Status ROHS3 Compliant

DG2731DN-T1-E4 Overview


The electronic component is convenient to ship overseas because it is packed in a 10-VFDFN Exposed Pad. In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. The multiplexer is located in Surface Mount. Multiplexers and demultiplexers have a ratio of 2:1. Operating temperature extended to -40°C~85°C TA. In total, 10 terminations have occurred. A electrical component with 1 channels is capable of high-quality output. An 3V voltage supply should allow the electrical part to be turned on and run. Into the electrical component body are injected 10 pins. SPDT switching circuits are used in these analog switch ics. It consists of 2 circuits. Look for analog switch ic variants by searching with DG2731. In this multiplexer, the internal resistance is 400mOhm. To find out what the 10 pins do, please refer to the datasheets. In this analog multiplexer, the value is Multiplexer or Switches. In normalcircumstances, users should not exceed 4.3V volts for the multiplexer. A cost-effective Single supply type analogue multiplexer. In order for the electronic part to function properly, the lowest voltage should be 1.65V. The analogue multiplexer could operate on 1μA current. Draining from a single voltage supply, this analog switch requires a voltage of 1.65V~4.3V. The switch multiplexer may be damaged if it is exposed to voltage greater than 1μA. There are SEPARATE OUTPUT outputs on this analog switch ic.

DG2731DN-T1-E4 Features


1 Channels
Switch Circuit: SPDT
1μA Supply Current

DG2731DN-T1-E4 Applications


There are a lot of Vishay Siliconix DG2731DN-T1-E4 Analog Switches & Multiplexers ICs applications.

  • Voice over IP/DSL – Integrated Access Devices, Smart
  • Remote Powered Equipment
  • Remote wireless modules
  • Battery Powered Systems
  • Routers
  • Avionics
  • Mechanical reed relay replacement
  • PBX interfaces
  • Video signal routing
  • Audio/video switches

Write a review

Note: HTML is not translated!
    Bad           Good