Parameters |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
75 dB |
Current - Leakage (IS(off)) (Max) |
1nA |
Channel Capacitance (CS(off), CD(off)) |
104pF |
On-state Resistance Match-Nom |
0.03Ohm |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
110ns, 30ns |
Charge Injection |
9pC |
Channel-to-Channel Matching (ΔRon) |
30m Ω |
Crosstalk |
-75dB @ 100kHz |
Switching |
BREAK-BEFORE-MAKE |
Voltage - Supply, Single (V+) |
1.65V~4.3V |
Drain to Source Resistance |
300mOhm |
Height Seated (Max) |
1.1mm |
Length |
3mm |
Width |
3mm |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
10-TFSOP, 10-MSOP (0.118, 3.00mm Width) |
Number of Pins |
10 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2009 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
10 |
Resistance |
400mOhm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
320mW |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
2 |
Supply Voltage |
3V |
Terminal Pitch |
0.5mm |
Reach Compliance Code |
unknown |
Time@Peak Reflow Temperature-Max (s) |
40 |
Base Part Number |
DG2731 |
Pin Count |
10 |
Number of Outputs |
4 |
Qualification Status |
Not Qualified |
Number of Channels |
1 |
Max Supply Voltage |
4.3V |
Min Supply Voltage |
1.6V |
Operating Supply Current |
1μA |
Power Dissipation |
320mW |
Max Supply Current |
1mA |
Turn On Delay Time |
110 ns |
Number of Inputs |
2 |
Supply Type |
Single |
Turn-Off Delay Time |
30 ns |
On-State Resistance (Max) |
450mOhm |
DG2731DQ-T1-E3 Overview
Shipping overseas is convenient due to the electrical component's packing in 10-TFSOP, 10-MSOP (0.118, 3.00mm Width). High reliability is ensured by the advanced packaging method Tape & Reel (TR). It is mounted in the position Surface Mount. Multiplexers and demultiplexers have the same number of circuits 2:1. Temperatures around -40°C~85°C TA are extended for operation. In total, 10 terminations have occurred. Due to its 1 channels, the electrical component produces high-quality output. In the case of a voltage supply of 3V volts, the electrical part can be powered up and run. An electrical component like this is included in the 10 series. These analog multiplexers are built based on SPDT switching circuits. Try searching with DG2731 if you're looking for variants. Internally, this switch multiplexer has a resistance of 400mOhm. To find out what the 10 pins do, please refer to the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. normally, users should not supply switches with voltages higher than 4.3V. Digital switch that provides Single power at a cost-effective price. The lowest voltage fed to the electronic component should be 1.6V. The analogue multiplexer could operate on 1μA current. This analogue multiplexer requires a voltage of 1.65V~4.3V when it drains from a single voltage supply. If put voltage greater than 1mA on the device, damage may be caused to the analogue multiplexer. The electrical component supports 2 inputs. This electronic component presents a Drain to Source resistance of 300mOhm. There are 4 outputs on the analogue multiplexer.
DG2731DQ-T1-E3 Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
Drain-to-Source resistance: 300mOhm
DG2731DQ-T1-E3 Applications
There are a lot of Vishay Siliconix DG2731DQ-T1-E3 Analog Switches & Multiplexers ICs applications.
- PCMCIA cards
- New designs requiring multiplexer functions
- Multi-Line E1 Interface Cards
- PBX interfaces
- Cross Connects
- USB 1.1 signal switching circuits
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Microwave transmission systems
- Avionics
- SONET