DG2732DQ-T1-E3
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 10 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| Resistance | 400mOhm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 320mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.5mm |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG2732 |
| Pin Count | 10 |
| Number of Outputs | 4 |
| Qualification Status | Not Qualified |
| Number of Channels | 1 |
| Max Supply Voltage | 4.3V |
| Min Supply Voltage | 1.6V |
| Operating Supply Current | 1μA |
| Power Dissipation | 320mW |
| Max Supply Current | 1mA |
| Turn On Delay Time | 110 ns |
| Number of Inputs | 2 |
| Supply Type | Single |
| Turn-Off Delay Time | 30 ns |
| On-State Resistance (Max) | 450mOhm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 104pF |
| On-state Resistance Match-Nom | 0.03Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 110ns, 30ns |
| Charge Injection | 9pC |
| Channel-to-Channel Matching (ΔRon) | 30m Ω |
| Crosstalk | -75dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.65V~4.3V |
| Height Seated (Max) | 1.1mm |
| Length | 3mm |
| Width | 3mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
DG2732DQ-T1-E3 Overview
The electronic component is convenient to ship overseas because it is packed in a 10-TFSOP, 10-MSOP (0.118, 3.00mm Width). Advanced packaging method Tape & Reel (TR) is used to provide high reliability. The multiplexer is located in Surface Mount. 2:1 is the ratio of multiplexer to demultiplexer circuits. Operating temperature extended to -40°C~85°C TA. Total terminations are 10. The electronic part provides high-quality output because it has 1 channels. Turning on and running the electrical part should be easy with a 3V voltage supply. An electrical component like this is included in the 10 series. SPDT switching circuits are used in these analog switch ics. Try searching with DG2732 if you're looking for variants. This digital multiplexer has 400mOhm internal resistance. To find out what the functions of 10 pins are, please refer to their datasheets. Theswitch device is a typical Multiplexer or Switches. In normalcircumstances, users should not exceed 4.3V volts for the multiplexer. Analog switch ics with Single supply type are cost-effective. 1.6V is the lowest voltage the electrical component should receive. 1μA current would be enough for this multiplexer to operate. The voltage required by this switch device is 1.65V~4.3V, draining from a single voltage supply. Put voltage above 1mA on the multiplexer to cause damage. It is possible to operate 2 inputs. Multiplexer ics with 4 outputs are available.
DG2732DQ-T1-E3 Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
DG2732DQ-T1-E3 Applications
There are a lot of Vishay Siliconix DG2732DQ-T1-E3 Analog Switches & Multiplexers ICs applications.
- Battery-powered systems
- Automatic test equipment
- Voice over IP/DSL – Integrated Access Devices, Smart
- Fiber In The Loop (FITL)
- Automotive applications
- Low-Voltage
- Battery Powered Systems
- Battery Powered Instruments
- Data switching
- MP3 players
