banner_page

DG2733DN-T1-E4

110ns, 30ns SPDT 450mOhm DUAL Analog Switches BREAK-BEFORE-MAKE DG2733 10 Pins 1nA 3V 10-VFDFN Exposed Pad


  • Manufacturer: Vishay Siliconix
  • Nocochips NO: 880-DG2733DN-T1-E4
  • Package: 10-VFDFN Exposed Pad
  • Datasheet: PDF
  • Stock: 511
  • Description: 110ns, 30ns SPDT 450mOhm DUAL Analog Switches BREAK-BEFORE-MAKE DG2733 10 Pins 1nA 3V 10-VFDFN Exposed Pad(Kg)

Details

Tags

Parameters
Mount Surface Mount
Mounting Type Surface Mount
Package / Case 10-VFDFN Exposed Pad
Number of Pins 10
Weight 50.008559mg
Operating Temperature -40°C~85°C TA
Packaging Tape & Reel (TR)
Published 2008
JESD-609 Code e4
Pbfree Code yes
Part Status Obsolete
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 10
Resistance 400mOhm
Terminal Finish Nickel/Palladium/Gold (Ni/Pd/Au)
Subcategory Multiplexer or Switches
Max Power Dissipation 1.191W
Technology CMOS
Terminal Position DUAL
Terminal Form NO LEAD
Peak Reflow Temperature (Cel) 260
Number of Functions 2
Supply Voltage 3V
Terminal Pitch 0.5mm
Reach Compliance Code unknown
Time@Peak Reflow Temperature-Max (s) 40
Base Part Number DG2733
Output SEPARATE OUTPUT
Pin Count 10
Qualification Status Not Qualified
Number of Channels 1
Number of Circuits 2
Max Supply Voltage 4.3V
Min Supply Voltage 1.65V
Operating Supply Current 1μA
Max Supply Current 1μA
Turn On Delay Time 110 ns
Supply Type Single
Turn-Off Delay Time 30 ns
On-State Resistance (Max) 450mOhm
Multiplexer/Demultiplexer Circuit 2:1
Off-state Isolation-Nom 75 dB
Current - Leakage (IS(off)) (Max) 1nA
Channel Capacitance (CS(off), CD(off)) 104pF
On-state Resistance Match-Nom 0.03Ohm
Switch Circuit SPDT
Switch Time (Ton, Toff) (Max) 110ns, 30ns
Charge Injection 9pC
Channel-to-Channel Matching (ΔRon) 30m Ω
Crosstalk -75dB @ 100kHz
Switching BREAK-BEFORE-MAKE
Voltage - Supply, Single (V+) 1.65V~4.3V
Height 880μm
Length 3mm
Width 3mm
RoHS Status ROHS3 Compliant

DG2733DN-T1-E4 Overview


The electrical component comes in 10-VFDFN Exposed Pad packaging, which makes it convenient to ship overseas. To ensure high reliability, a new packaging method Tape & Reel (TR) is used. Multiplexers like this are mounted in the Surface Mount position. The ratio between the number of multiplexer and demultiplexer circuits is 2:1. Around -40°C~85°C TA is the extended operating temperature. 10 terminations have been made so far. By its 1 channels, the electronic component provides high-quality output. In the case of a voltage supply of 3V volts, the electrical part can be powered up and run. Into the electrical component body are injected 10 pins. The analog switch ics are built using SPDT switching circuits. It consists of 2 circuits. Try searching with DG2733 if you're looking for variants. Internally, this switch multiplexer has a resistance of 400mOhm. Datasheets for 10 pin functions are available upon request. A analogue multiplexer of this type is a Multiplexer or Switches. Users shouldn't supply more than 4.3V voltage to the switch device. Single supply type digital switch with a low cost. A low voltage of 1.65V should be applied to the electronic component. The switch device would be able to operate with 1μA current. Using a single voltage supply, this switch device consumes 1.65V~4.3V volts. A digital multiplexer may suffer damage if voltage is applied above 1μA. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them.

DG2733DN-T1-E4 Features


1 Channels
Switch Circuit: SPDT
1μA Supply Current

DG2733DN-T1-E4 Applications


There are a lot of Vishay Siliconix DG2733DN-T1-E4 Analog Switches & Multiplexers ICs applications.

  • Medical
  • Optical Applications
  • SONET
  • Video signal routing
  • Low-Voltage
  • Private Branch Exchange (PBX)
  • DSUs
  • Existing multiplexer applications (both fault-protected and nonfault-protected)
  • Switching Systems
  • Microprocessor Controlled Analog Systems

Write a review

Note: HTML is not translated!
    Bad           Good