Parameters |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
10-TFSOP, 10-MSOP (0.118, 3.00mm Width) |
Number of Pins |
10 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2009 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
10 |
Termination |
SMD/SMT |
Resistance |
400mOhm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
320mW |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
2 |
Supply Voltage |
3V |
Terminal Pitch |
0.5mm |
Reach Compliance Code |
unknown |
Time@Peak Reflow Temperature-Max (s) |
40 |
Base Part Number |
DG2733 |
Pin Count |
10 |
Number of Outputs |
4 |
Qualification Status |
Not Qualified |
Number of Channels |
1 |
Max Supply Voltage |
4.3V |
Min Supply Voltage |
1.65V |
Operating Supply Current |
1μA |
Power Dissipation |
320mW |
Max Supply Current |
1mA |
Turn On Delay Time |
110 ns |
Number of Inputs |
2 |
Supply Type |
Single |
Turn-Off Delay Time |
30 ns |
On-State Resistance (Max) |
450mOhm |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
75 dB |
Current - Leakage (IS(off)) (Max) |
1nA |
Channel Capacitance (CS(off), CD(off)) |
104pF |
On-state Resistance Match-Nom |
0.03Ohm |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
110ns, 30ns |
Charge Injection |
9pC |
Channel-to-Channel Matching (ΔRon) |
30m Ω |
Crosstalk |
-75dB @ 100kHz |
Switching |
BREAK-BEFORE-MAKE |
Voltage - Supply, Single (V+) |
1.65V~4.3V |
Drain to Source Resistance |
300mOhm |
Height Seated (Max) |
1.1mm |
Length |
3mm |
Width |
3mm |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
DG2733DQ-T1-E3 Overview
The electronic part can be shipped overseas conveniently because it is packaged in 10-TFSOP, 10-MSOP (0.118, 3.00mm Width). This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). Surface Mount is where this multiplexer is located. 2:1 is the ratio between multiplexers and demultiplexers. Temperatures around -40°C~85°C TA are extended for operation. Totally, there are 10 terminations. By its 1 channels, the electronic component provides high-quality output. When the electronic component is given a voltage of 3V, it should be turned on and run. There are 10 pins injected into the electronic part body. A SPDT switching circuit is used for these analog switches. Try searching for DG2733 variants of the analog switch ic. There is 400mOhm internal resistance in this digital multiplexer. The datasheets for the 10 pins explain the functions. The analog multiplexer shown here is a typical Multiplexer or Switches. In normalcircumstances, users should not exceed 4.3V volts for the multiplexer. The analog switch ic is of the Single supply type and is cost-effective. A low voltage of 1.65V should be applied to the electronic component. The analogue multiplexer could operate on 1μA current. Analogue multiplexers require a 1.65V~4.3V voltage to drain from a single voltage supply. Put voltage above 1mA on the multiplexer to cause damage. Among the inputs that can be operated are the 2 inputs. It has a Drain to Source resistance of 300mOhm ohms. There are 4 outputs on the analogue multiplexer.
DG2733DQ-T1-E3 Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
Drain-to-Source resistance: 300mOhm
DG2733DQ-T1-E3 Applications
There are a lot of Vishay Siliconix DG2733DQ-T1-E3 Analog Switches & Multiplexers ICs applications.
- PDH Multiplexers
- ATM
- Voice over IP/DSL – Integrated Access Devices, Smart
- Frame Relay Equipment
- Signal routing between systems
- Communications systems
- Multiplexers
- Industrial control systems
- Battery Powered Instruments
- PCMCIA cards