DG2735ADN-T1-GE4
| Parameters | |
|---|---|
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| Resistance | 500mOhm |
| Terminal Finish | NICKEL PALLADIUM GOLD |
| Max Power Dissipation | 208mW |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | NO LEAD |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Reach Compliance Code | unknown |
| Base Part Number | DG2735 |
| Pin Count | 10 |
| Number of Outputs | 4 |
| Number of Channels | 1 |
| Max Supply Voltage | 4.3V |
| Min Supply Voltage | 1.65V |
| Operating Supply Current | 1μA |
| Power Dissipation | 208mW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 78 ns |
| Number of Inputs | 2 |
| Supply Type | Single |
| Turn-Off Delay Time | 58 ns |
| -3db Bandwidth | 50MHz |
| On-State Resistance (Max) | 500mOhm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 70 dB |
| Current - Leakage (IS(off)) (Max) | 2nA |
| Channel Capacitance (CS(off), CD(off)) | 55pF |
| On-state Resistance Match-Nom | 0.06Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 78ns, 58ns |
| Channel-to-Channel Matching (ΔRon) | 60m Ω |
| Crosstalk | -70dB @ 100kHz |
| Switch-on Time-Max | 80ns |
| Switch-off Time-Max | 60ns |
| Voltage - Supply, Single (V+) | 1.65V~4.3V |
| Height Seated (Max) | 0.6mm |
| Length | 1.8mm |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 10-UFQFN |
| Number of Pins | 10 |
| Weight | 7.002332mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2016 |
DG2735ADN-T1-GE4 Overview
The electronic part can be shipped overseas conveniently because it is packaged in 10-UFQFN. This packaging method provides high reliability because it uses advanced packaging techniques. In Surface Mount, you'll find this switch device. The ratio between the number of multiplexer and demultiplexer circuits is 2:1. The operating temperature is extended to around -40°C~85°C TA. The total number of terminations is 10. The electronic part delivers high-quality output through its 1 channels. It is safe to turn on and run the electronic component with a 3V voltage supply. An electrical component of this type can be found in the 10 series. SPDT switching circuits are used in these analog switch ics. Using the DG2735 search parameter, you can discover variants of the switch. An switch multiplexer with 500mOhm internal resistance has a value of 500mOhm. For functions related to 10 pins, please refer to the datasheets. normally, users should not supply switches with voltages higher than 4.3V. Single supply type digital switch with a low cost. The lowest voltage fed to the electronic component should be 1.65V. This digital switch can be operated with a current of 1μA. A voltage of 1.65V~4.3V is required to drain this analog switch from a single voltage supply. Putting voltage greater than 1μA on the multiplexer may cause damage. The 2 inputs need to be operated in order to work. 4 outputs are included in the analogue multiplexer.
DG2735ADN-T1-GE4 Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
-3db Bandwidth: 50MHz
DG2735ADN-T1-GE4 Applications
There are a lot of Vishay Siliconix DG2735ADN-T1-GE4 Analog Switches & Multiplexers ICs applications.
- Battery Powered Systems
- Residential Gateways, Home Gateway/Router
- Microprocessor controlled systems
- Multi-Line E1 Interface Cards
- Audio and video signal routing
- Communication systems
- Digital cross connects (DSX-1)
- Relay Replacement
- DSUs
- Low-Voltage
