DG2735DN-T1-E4
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-UFQFN |
| Number of Pins | 8 |
| Weight | 7.002332mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2016 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| Resistance | 500mOhm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 208mW |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG2735 |
| Pin Count | 10 |
| JESD-30 Code | R-XQCC-N10 |
| Number of Outputs | 4 |
| Qualification Status | Not Qualified |
| Power Supplies | 3V |
| Number of Channels | 1 |
| Max Supply Voltage | 4.3V |
| Min Supply Voltage | 1.65V |
| Operating Supply Current | 1μA |
| Power Dissipation | 208mW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 78 ns |
| Number of Inputs | 2 |
| Supply Type | Single |
| Turn-Off Delay Time | 58 ns |
| -3db Bandwidth | 50MHz |
| On-State Resistance (Max) | 500mOhm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 70 dB |
| Current - Leakage (IS(off)) (Max) | 2nA |
| Channel Capacitance (CS(off), CD(off)) | 55pF |
| On-state Resistance Match-Nom | 0.06Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 78ns, 58ns |
| Channel-to-Channel Matching (ΔRon) | 60m Ω |
| Crosstalk | -70dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 60ns |
| Voltage - Supply, Single (V+) | 1.65V~4.3V |
| Height | 550μm |
| Length | 1.8mm |
| Width | 1.4mm |
| RoHS Status | ROHS3 Compliant |
DG2735DN-T1-E4 Overview
Shipping overseas is convenient due to the electrical component's packing in 8-UFQFN. This packaging method provides high reliability because it uses advanced packaging techniques. This analog switch is mounted in Surface Mount. 2:1 is the number of circuits in the multiplexer and demultiplexer. Operating temperature extended to -40°C~85°C TA. There are 10 terminations totally. This electronic part offers high-quality output due to its 1 channels. Powered by a 3V voltage supply, the electrical part should be switched on and run. As part of its design, the 10 series is equipped with this electronic component. A SPDT switching circuit is used for these analog switches. Use DG2735 to search for variants of the digital switches. Analog switches have 500mOhm internal resistance. For details about the functions of 8 pins, please refer to the datasheets. Theswitch device is a typical Multiplexer or Switches. Multiplexers should not be powered above 4.3V in normal situations. A cost-effective Single supply type analogue multiplexer. It is recommended that the electrical component receives a voltage of 1.65V. It would be sufficient to run this analogue multiplexer with 1μA current. Using a single voltage supply, this switch device consumes 1.65V~4.3V volts. It may damage the digital multiplexer if the voltage is higher than 1μA. The 2 inputs need to be operated in order to work. The analog switch ics has 4 outputs.
DG2735DN-T1-E4 Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
-3db Bandwidth: 50MHz
DG2735DN-T1-E4 Applications
There are a lot of Vishay Siliconix DG2735DN-T1-E4 Analog Switches & Multiplexers ICs applications.
- Precision instrumentation
- Multi-Line E1 Interface Cards
- Optical Applications
- FTTH
- Data Acquisition Systems
- ISDN NT1/TA
- Fiber In The Loop (FITL)
- MP3 players
- Residential Gateways, Home Gateway/Router
- Frame Relay Equipment
