DG2736DN-T1-E4
| Parameters | |
|---|---|
| Operating Supply Current | 1μA |
| Power Dissipation | 208mW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 78 ns |
| Number of Inputs | 2 |
| Supply Type | Single |
| Turn-Off Delay Time | 58 ns |
| -3db Bandwidth | 50MHz |
| On-State Resistance (Max) | 500mOhm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 70 dB |
| Current - Leakage (IS(off)) (Max) | 2nA |
| Channel Capacitance (CS(off), CD(off)) | 55pF |
| On-state Resistance Match-Nom | 0.06Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 78ns, 58ns |
| Channel-to-Channel Matching (ΔRon) | 60m Ω |
| Crosstalk | -70dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 80ns |
| Switch-off Time-Max | 60ns |
| Voltage - Supply, Single (V+) | 1.65V~4.3V |
| Height | 550μm |
| Length | 1.8mm |
| Width | 1.4mm |
| RoHS Status | ROHS3 Compliant |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 10-UFQFN |
| Number of Pins | 10 |
| Weight | 7.002332mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| Resistance | 500mOhm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 208mW |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG2736 |
| Pin Count | 10 |
| Number of Outputs | 4 |
| Qualification Status | Not Qualified |
| Power Supplies | 3V |
| Number of Channels | 1 |
| Max Supply Voltage | 4.3V |
| Min Supply Voltage | 1.65V |
DG2736DN-T1-E4 Overview
Due to its 10-UFQFN packaging, the electronic part is convenient for international shipping. A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). There is an analog multiplexer mounted in position Surface Mount. There is 2:1 ratio between the number of multiplexers and demultiplexers. An extended operating temperature of -40°C~85°C TA degrees Celsius. In total, there have been 10 terminations. The electronic part provides high-quality output because it has 1 channels. Powered by a 3V voltage supply, the electrical part should be switched on and run. The electrical component body receives 10 pins. Based on SPDT switching circuits, these analog multiplexers work. If you are looking for variants of the digital switch, trying search with DG2736. In this multiplexer, the internal resistance is 500mOhm. For functions related to 10 pins, please refer to the datasheets. Multiplexer or Switches is a typical switch device. It is generally not recommended to supply a voltage higher than 4.3V to the switch device in normal circumstances. The digital multiplexer has a low cost Single supply. It is recommended that the electrical component receives a voltage of 1.65V. 1μA current would be enough for this multiplexer to operate. Using only a single voltage supply, this analog switch requires 1.65V~4.3V voltage. The switch multiplexer may be damaged if it is exposed to voltage greater than 1μA. Among the inputs that can be operated are the 2 inputs. An output of 4 is provided by the digital multiplexer.
DG2736DN-T1-E4 Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
-3db Bandwidth: 50MHz
DG2736DN-T1-E4 Applications
There are a lot of Vishay Siliconix DG2736DN-T1-E4 Analog Switches & Multiplexers ICs applications.
- Remote wireless modules
- Wireless Local Loop
- Video signal routing
- Power routing
- PBXs
- DVD-R
- Optical Applications
- SONET/SDH ADM
- Avionics and Military Systems
- Industrial and process control systems
