Parameters |
Qualification Status |
Not Qualified |
Power Supplies |
3V |
Number of Channels |
1 |
Number of Circuits |
1 |
Max Supply Voltage |
4.3V |
Min Supply Voltage |
2.3V |
Operating Supply Current |
1μA |
Max Supply Current |
1μA |
Throw Configuration |
SPST |
Turn On Delay Time |
60 ns |
Supply Type |
Single |
Turn-Off Delay Time |
50 ns |
-3db Bandwidth |
720MHz |
On-State Resistance (Max) |
8Ohm |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
28 dB |
Current - Leakage (IS(off)) (Max) |
10nA |
Channel Capacitance (CS(off), CD(off)) |
4.4pF 3.8pF |
On-state Resistance Match-Nom |
0.1Ohm |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
60ns, 50ns |
Charge Injection |
10.4pC |
Channel-to-Channel Matching (ΔRon) |
100m Ω |
Crosstalk |
-109dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
70ns |
Voltage - Supply, Single (V+) |
2.3V~4.3V |
Normal Position |
NC |
Height Seated (Max) |
0.6mm |
RoHS Status |
ROHS3 Compliant |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
8-UFQFN |
Number of Pins |
8 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2013 |
JESD-609 Code |
e4 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
8 |
Resistance |
8Ohm |
Terminal Finish |
Nickel/Palladium/Gold (Ni/Pd/Au) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
190mW |
Technology |
CMOS |
Terminal Position |
QUAD |
Terminal Form |
NO LEAD |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
2 |
Supply Voltage |
3V |
Terminal Pitch |
0.4mm |
Reach Compliance Code |
unknown |
Time@Peak Reflow Temperature-Max (s) |
40 |
Base Part Number |
DG2737 |
Output |
SEPARATE OUTPUT |
Pin Count |
8 |
DG2737DN-T1-E4 Overview
Due to its 8-UFQFN packaging, the electronic part is convenient for international shipping. The advanced packaging method Tape & Reel (TR) provides high reliability. The multiplexer is located in Surface Mount. Multiplexers and demultiplexers have a ratio of 2:1. Around -40°C~85°C TA is the extended operating temperature. A total of 8 terminations have been recorded. A electrical component with 1 channels is capable of high-quality output. In the case of a voltage supply of 3V volts, the electrical part can be powered up and run. Into the electrical component body are injected 8 pins. These analog multiplexers are built based on SPDT switching circuits. A total of 1 circuits make up this switch device. Search with DG2737 if you are looking for analog multiplexer variants. Analog switches have 8Ohm internal resistance. The datasheets for the 8 pins explain the functions. There is Multiplexer or Switches analog multiplexer like this in the world. normally, users should not supply switches with voltages higher than 4.3V. Analogue multiplexer with a Single supply type that is cost-effective. It is recommended to use 2.3V as the lowest voltage for the electrical part. For this digital switch to work, 1μA current would suffice. This analog switch requires a voltage of 2.3V~4.3V to drain from a single voltage supply. A digital multiplexer may suffer damage if voltage is applied above 1μA. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them.
DG2737DN-T1-E4 Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
-3db Bandwidth: 720MHz
DG2737DN-T1-E4 Applications
There are a lot of Vishay Siliconix DG2737DN-T1-E4 Analog Switches & Multiplexers ICs applications.
- PCMCIA cards
- HDTV
- Microprocessor Controlled Analog Systems
- Signal routing between systems
- High reliability control systems
- Microprocessor controlled systems
- Microwave transmission systems
- Frame Relay Equipment
- Medical Instrumentation
- Transmit