banner_page

DG2738DN-T1-E4

60ns, 50ns SPST - NC 8Ohm QUAD Analog Switches BREAK-BEFORE-MAKE DG2738 8 Pins 10nA 3V 8-UFQFN


  • Manufacturer: Vishay Siliconix
  • Nocochips NO: 880-DG2738DN-T1-E4
  • Package: 8-UFQFN
  • Datasheet: PDF
  • Stock: 801
  • Description: 60ns, 50ns SPST - NC 8Ohm QUAD Analog Switches BREAK-BEFORE-MAKE DG2738 8 Pins 10nA 3V 8-UFQFN(Kg)

Details

Tags

Parameters
Mount Surface Mount
Mounting Type Surface Mount
Package / Case 8-UFQFN
Number of Pins 8
Operating Temperature -40°C~85°C TA
Packaging Tape & Reel (TR)
Published 2013
JESD-609 Code e4
Pbfree Code yes
Part Status Obsolete
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 8
Resistance 8Ohm
Terminal Finish Nickel/Palladium/Gold (Ni/Pd/Au)
Subcategory Multiplexer or Switches
Max Power Dissipation 190mW
Technology CMOS
Terminal Position QUAD
Terminal Form NO LEAD
Peak Reflow Temperature (Cel) 260
Number of Functions 2
Supply Voltage 3V
Terminal Pitch 0.4mm
Reach Compliance Code unknown
Time@Peak Reflow Temperature-Max (s) 40
Base Part Number DG2738
Output SEPARATE OUTPUT
Pin Count 8
Qualification Status Not Qualified
Power Supplies 3V
Number of Channels 1
Number of Circuits 2
Max Supply Voltage 4.3V
Min Supply Voltage 2.3V
Operating Supply Current 1μA
Max Supply Current 1μA
Throw Configuration SPST
Turn On Delay Time 60 ns
Supply Type Single
Turn-Off Delay Time 50 ns
-3db Bandwidth 720MHz
On-State Resistance (Max) 8Ohm
Multiplexer/Demultiplexer Circuit 1:1
Off-state Isolation-Nom 28 dB
Current - Leakage (IS(off)) (Max) 10nA
Channel Capacitance (CS(off), CD(off)) 4.4pF 3.8pF
On-state Resistance Match-Nom 0.1Ohm
Switch Circuit SPST - NC
Switch Time (Ton, Toff) (Max) 60ns, 50ns
Charge Injection 10.4pC
Channel-to-Channel Matching (ΔRon) 100m Ω
Crosstalk -109dB @ 1MHz
Switching BREAK-BEFORE-MAKE
Switch-on Time-Max 70ns
Voltage - Supply, Single (V+) 2.3V~4.3V
Normal Position NC
Height Seated (Max) 0.6mm
Length 1.4mm
RoHS Status ROHS3 Compliant

DG2738DN-T1-E4 Overview


As the electronic part is packed in 8-UFQFN, international shipping is convenient. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). Surface Mount is where this multiplexer is located. Multiplexers and demultiplexers have a ratio of 1:1. Operational temperature extended around -40°C~85°C TA. Totally, there are 8 terminations. Due to its 1 channels, the electrical component produces high-quality output. With a 3V voltage supply, the electrical component should be turned on and run. It is injected into the electrical part body with 8 pins. Multiplexers built on a SPST - NC switching circuit are built. The multiplexer consists of 2 circuits. DG2738 can be used to search for analog multiplexer variants. This digital multiplexer has 8Ohm internal resistance. Datasheets for 8 pin functions are available upon request. Multiplexer or Switches is a typical switch device. Users should never supply a voltage higher than 4.3V to a switch device. An effective Single supply digital multiplexer. A low voltage of 2.3V should be applied to the electronic component. 1μA current would be enough for this multiplexer to operate. A voltage of 2.3V~4.3V is required to drain this analog switch from a single voltage supply. Putting voltage greater than 1μA on the multiplexer may cause damage. The digital multiplexer has SEPARATE OUTPUT outputs that can be used.

DG2738DN-T1-E4 Features


1 Channels
Switch Circuit: SPST - NC
1μA Supply Current
-3db Bandwidth: 720MHz

DG2738DN-T1-E4 Applications


There are a lot of Vishay Siliconix DG2738DN-T1-E4 Analog Switches & Multiplexers ICs applications.

  • Switching Systems
  • Digital cross connects (DSX-1)
  • Avionics
  • SONET/SDH ADM
  • Audio and video routing
  • Existing multiplexer applications (both fault-protected and nonfault-protected)
  • SONET
  • Signal routing between systems
  • Remote Powered Equipment
  • Data switching

Write a review

Note: HTML is not translated!
    Bad           Good