Parameters |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad |
Number of Pins |
8 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2013 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
8 |
Resistance |
8Ohm |
Terminal Finish |
MATTE TIN |
Additional Feature |
VIDEO APPLICATION |
Subcategory |
Multiplexer or Switches |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
2 |
Supply Voltage |
1.8V |
Terminal Pitch |
0.65mm |
Reach Compliance Code |
unknown |
Time@Peak Reflow Temperature-Max (s) |
40 |
Base Part Number |
DG2741 |
Output |
SEPARATE OUTPUT |
Pin Count |
8 |
Qualification Status |
Not Qualified |
Operating Supply Voltage |
3V |
Number of Channels |
1 |
Max Supply Voltage |
3.6V |
Min Supply Voltage |
1.5V |
Operating Supply Current |
10nA |
Nominal Supply Current |
10nA |
Max Supply Current |
1μA |
Throw Configuration |
SPST |
Turn On Delay Time |
45 ns |
Number of Inputs |
2 |
Supply Type |
Single |
Turn-Off Delay Time |
40 ns |
On-State Resistance (Max) |
800mOhm |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
55 dB |
Current - Leakage (IS(off)) (Max) |
1nA |
Channel Capacitance (CS(off), CD(off)) |
81pF |
On-state Resistance Match-Nom |
0.05Ohm |
Switch Circuit |
SPST - NO |
Switch Time (Ton, Toff) (Max) |
30ns, 28ns |
Charge Injection |
5.8pC |
Crosstalk |
-89dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
50ns |
Voltage - Supply, Single (V+) |
1.5V~3.6V |
Normal Position |
NO |
Height |
850μm |
Length |
3mm |
Width |
3mm |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
DG2741DQ-T1-E3 Overview
The electronic part can be shipped overseas conveniently because it is packaged in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad. To ensure high reliability, a new packaging method Tape & Reel (TR) is used. It is mounted in the position Surface Mount. Multiplexers and demultiplexers have the same number of circuits 1:1. Operation at a temperature around -40°C~85°C TA. 8 terminations have been made so far. By its 1 channels, the electronic component provides high-quality output. An 1.8V voltage supply should allow the electrical part to be turned on and run. There are 8 pins injected into the electronic part body. Based on SPST - NO switching circuits, these analog multiplexers work. Try searching with DG2741 if you're looking for variants. There is 8Ohm internal resistance in this digital multiplexer. To find out what the 8 pins do, please refer to the datasheets. In this analog multiplexer, the value is Multiplexer or Switches. A voltage higher than 3.6V should not normally be supplied to the switches. Digital switch that provides Single power at a cost-effective price. It is recommended that the electrical component receives a voltage of 1.5V. This multiplexer would work with 10nA current. An analogue multiplexer drains from a single voltage supply at 1.5V~3.6V. A digital multiplexer may suffer damage if voltage is applied above 1μA. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer. Operating voltages range from 3V. Operating the 2 inputs requires 2 inputs. This electrical component also includes additional features such as VIDEO APPLICATION.
DG2741DQ-T1-E3 Features
1 Channels
Switch Circuit: SPST - NO
10nA Supply Current
Additional Features: VIDEO APPLICATION
DG2741DQ-T1-E3 Applications
There are a lot of Vishay Siliconix DG2741DQ-T1-E3 Analog Switches & Multiplexers ICs applications.
- Multi-Line E1 Interface Cards
- Precision instrumentation
- Switching Systems
- Audio and video signal routing
- Audio and video routing
- DSLAMs
- Battery Powered Instruments
- Automatic test equipment
- Avionics
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads