DG2742DQ-T1-E3
| Parameters | |
|---|---|
| Max Supply Voltage | 3.6V |
| Min Supply Voltage | 1.5V |
| Operating Supply Current | 10nA |
| Nominal Supply Current | 10nA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 45 ns |
| Number of Inputs | 2 |
| Supply Type | Single |
| Turn-Off Delay Time | 40 ns |
| On-State Resistance (Max) | 800mOhm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 55 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 81pF |
| On-state Resistance Match-Nom | 0.05Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 30ns, 28ns |
| Charge Injection | 5.8pC |
| Crosstalk | -89dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 50ns |
| Voltage - Supply, Single (V+) | 1.5V~3.6V |
| Normal Position | NC |
| Height Seated (Max) | 1.1mm |
| Length | 3mm |
| Width | 3mm |
| RoHS Status | ROHS3 Compliant |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2013 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Termination | SMD/SMT |
| Resistance | 8Ohm |
| Terminal Finish | MATTE TIN |
| Additional Feature | VIDEO APPLICATION |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 1.8V |
| Terminal Pitch | 0.65mm |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | DG2742 |
| Output | SEPARATE OUTPUT |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Number of Channels | 1 |
DG2742DQ-T1-E3 Overview
Shipping overseas is convenient with the electronic component packed in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) Exposed Pad. This packaging method provides high reliability because it uses advanced packaging techniques. Surface Mount is where this multiplexer is located. Multiplexers and demultiplexers have a number of circuits 1:1. Operation at a temperature around -40°C~85°C TA. Total terminations are 8. By its 1 channels, the electronic component provides high-quality output. Turning on and running the electrical part should be easy with a 1.8V voltage supply. Electronic part bodies are injected with 8 pins. Unlike digital switches, these are based on SPST - NC switching circuits. Using the DG2742 search parameter, you can discover variants of the switch. It has an internal resistance of 8Ohm. The functions of 8 pins can be found in the datasheets. In this analog multiplexer, the value is Multiplexer or Switches. Multiplexers should not be powered above 3.6V in normal situations. Analogue multiplexer with a Single supply type that is cost-effective. A low voltage of 1.5V should be applied to the electronic component. 10nA current would be enough for this multiplexer to operate. An analogue multiplexer drains from a single voltage supply at 1.5V~3.6V. When the digital multiplexer is charged above 1μA, damage can occur. The outputs of this digital multiplexer are SEPARATE OUTPUT in number. It is possible to operate 2 inputs. Don't forget the additional features of this electronic part, such as: VIDEO APPLICATION.
DG2742DQ-T1-E3 Features
1 Channels
Switch Circuit: SPST - NC
10nA Supply Current
Additional Features: VIDEO APPLICATION
DG2742DQ-T1-E3 Applications
There are a lot of Vishay Siliconix DG2742DQ-T1-E3 Analog Switches & Multiplexers ICs applications.
- Fault Tolerant Systems
- Sample hold systems
- T1/E1 Terminals
- Fiber to the Home
- Relay Replacement
- Data Acquisition Systems
- Low-Voltage
- Industrial and process control systems
- Channelized and Unchannelized DS3 applications
- Intelligent PBX
