banner_page

DG2742DS-T1-E3

30ns, 28ns SPST - NC 800mOhm DUAL Analog Switches BREAK-BEFORE-MAKE DG2742 8 Pins 1nA 1.8V SOT-23-8


  • Manufacturer: Vishay Siliconix
  • Nocochips NO: 880-DG2742DS-T1-E3
  • Package: SOT-23-8
  • Datasheet: PDF
  • Stock: 751
  • Description: 30ns, 28ns SPST - NC 800mOhm DUAL Analog Switches BREAK-BEFORE-MAKE DG2742 8 Pins 1nA 1.8V SOT-23-8(Kg)

Details

Tags

Parameters
Mount Surface Mount
Mounting Type Surface Mount
Package / Case SOT-23-8
Number of Pins 8
Operating Temperature -40°C~85°C TA
Packaging Tape & Reel (TR)
Published 2016
JESD-609 Code e3
Pbfree Code yes
Part Status Obsolete
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 8
Resistance 8Ohm
Terminal Finish MATTE TIN
Additional Feature VIDEO APPLICATION
Subcategory Multiplexer or Switches
Technology CMOS
Terminal Position DUAL
Terminal Form GULL WING
Peak Reflow Temperature (Cel) 260
Number of Functions 2
Supply Voltage 1.8V
Terminal Pitch 0.65mm
Reach Compliance Code unknown
Time@Peak Reflow Temperature-Max (s) 10
Base Part Number DG2742
Output SEPARATE OUTPUT
Pin Count 8
Qualification Status Not Qualified
Number of Channels 1
Max Supply Voltage 3.6V
Min Supply Voltage 1.5V
Operating Supply Current 10nA
Nominal Supply Current 10nA
Max Supply Current 1μA
Throw Configuration SPST
Turn On Delay Time 45 ns
Number of Inputs 2
Supply Type Single
Turn-Off Delay Time 40 ns
On-State Resistance (Max) 800mOhm
Multiplexer/Demultiplexer Circuit 1:1
Off-state Isolation-Nom 55 dB
Current - Leakage (IS(off)) (Max) 1nA
Channel Capacitance (CS(off), CD(off)) 81pF
On-state Resistance Match-Nom 0.05Ohm
Switch Circuit SPST - NC
Switch Time (Ton, Toff) (Max) 30ns, 28ns
Charge Injection 5.8pC
Crosstalk -89dB @ 1MHz
Switching BREAK-BEFORE-MAKE
Switch-on Time-Max 50ns
Voltage - Supply, Single (V+) 1.5V~3.6V
Normal Position NC
Height Seated (Max) 1.45mm
Width 1.65mm
RoHS Status ROHS3 Compliant

DG2742DS-T1-E3 Overview


Shipping overseas is convenient with the electronic component packed in SOT-23-8. To ensure high reliability, a new packaging method Tape & Reel (TR) is used. It is mounted in the position Surface Mount. 1:1 is the ratio between multiplexers and demultiplexers. Increasing operating temperature to around -40°C~85°C TA. Total terminations are 8. The electronic part delivers high-quality output through its 1 channels. In the case of a voltage supply of 1.8V volts, the electrical part can be powered up and run. A total of 8 pins are injected into the body of the electronic part. Circuits based on SPST - NC switching are used to construct these analog switch ics. Using the DG2742 search parameter, you can discover variants of the switch. In this multiplexer, the internal resistance is 8Ohm. The datasheets for the 8 pins explain the functions. In this analog multiplexer, the value is Multiplexer or Switches. In normalcircumstances, users should not exceed 3.6V volts for the multiplexer. Single supply type digital switch with a low cost. The lowest voltage fed to the electronic component should be 1.5V. The analogue multiplexer could operate on 10nA current. An analogue multiplexer drains from a single voltage supply at 1.5V~3.6V. It may damage the digital multiplexer if the voltage is higher than 1μA. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer. A 2 input needs to be operated. Additional features include: VIDEO APPLICATION.

DG2742DS-T1-E3 Features


1 Channels
Switch Circuit: SPST - NC
10nA Supply Current
Additional Features: VIDEO APPLICATION

DG2742DS-T1-E3 Applications


There are a lot of Vishay Siliconix DG2742DS-T1-E3 Analog Switches & Multiplexers ICs applications.

  • DVD-R
  • Cell phones
  • PBXs
  • Channel Banks
  • RGB switches
  • Automatic test equipment
  • Audio signal routing
  • Communication systems
  • Cross Connects
  • Medical systems

Write a review

Note: HTML is not translated!
    Bad           Good